Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S
SUS304 stainless variant (-S)The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S
The PEB4M5-S is an AirTAC PEB male branch tee in the SUS304 stud variant. It screws an M5x0.8 male thread into a port and splits the supply into two Dia 4 mm one-touch tube lines, so a single feed can drive two small actuators or one actuator plus a signal line. Connection is push-to-connect: push the tube home until it bottoms, the chuck grips it against the stainless spring gasket, and pressing the POM release button frees it again.
Because this code carries the -S suffix, the threaded stud is SUS304 stainless steel while the tee body stays PBT - this is not a solid stainless fitting. Ratings are identical to the standard resin line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa and a temperature window of -20 to +70 C. Unlike the larger threaded parts that arrive with sealant, the M5 size seals with a gasket on the thread face, so no thread tape is needed on the port.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S Is Used
Robot gripper vacuum branch
On a small SCARA pick-and-place head, an M5 vacuum port from the ejector can be split to two suction cups using this tee, with 4 mm polyurethane tube routing around the wrist where every gram and millimetre counts.
Analytical instrument air sampling tee
In a laboratory gas analyser or sample-handling rig, the SUS304 stud resists corrosion from occasional condensation or mild reagent splash while the PBT body keeps the fitting light and non-conductive near sensors.
Manifold signal tap on a packaging machine
A compact valve manifold with M5 ports can feed both an air flag indicator and a small pilot actuator from one port, replacing two separate connectors and a threaded junction in a crowded backplane.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S the Right Part?
Dia 4 mm is the smallest tube this fitting is made in on the M5 row, so there is no step down - the only neighbour is PEB6M5-S at Dia 6 mm, which buys a slightly larger bore for shorter fill times on a marginally longer run. If you need Dia 8 or Dia 10 tube, you must step the thread up to PEB401 (1/8 in), which opens those tube sizes on the same branch-tee shape. Whatever you choose, the tube OD must match exactly: a Dia 4 mm chuck will not seal on 5/32 in or 1/4 in tube, even though the difference looks trivial on a ruler.
Match the M5 thread to the actual port - M5x0.8 is the fine thread found on compact valve and cylinder ports, and it seals by gasket, not by winding. If the port is a tapered 1/8 in PT boss, order PEB401-S instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. It joins Dia 4 mm soft nylon or polyurethane tube on two legs with an M5x0.8 male thread (PT thread standard, sealed by gasket on the M5 size). The -S variant has a SUS304 stainless stud and a PBT body; all pressure and temperature figures are the same as the standard PEB4M5.
No. On the PEB branch-tee family the -S suffix means only the threaded stud is SUS304; the tee body remains PBT with a POM release button and NBR O-ring. If you need a fully stainless body, the -S suffix does that only on the PC and POC straight connectors. Do not re-rate this part either - it carries the same 0-1.0 MPa and -20 to +70 C limits as the standard version.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.