Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D
The PEB4M5D is an AirTAC PEB male branch tee, the smallest M5 size in the range. It mates Dia 4 mm soft nylon or polyurethane tubing with an M5x0.8 male thread, and adds a 90-degree branch so a drop line can be taken off a straight run without adding a separate union. The D suffix makes the fitting body black - on PEB this changes the body colour, not just the release button as on PC.
One-touch action: push the tube into the chuck and the stainless spring gasket and NBR O-ring grip and seal it; press the POM release ring and the tube comes free. This resin-profile fitting is rated 0-1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. Construction is POM button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring and a brass stud.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D Is Used
Mini gripper feed on an assembly head
Electronics assembly heads use M5 ports on compact grippers and mini slides; the branch tee lets one M5 feed serve both a supply drop and a pressure-tap line on a 4 mm tube run.
Pilot signal take-off inside a control panel
Branch a 4 mm pilot line off a main drop to feed a small solenoid valve or pressure switch, screwing the M5 stud straight into the valve port without extra adapters.
Lab dosing and sampling manifolds
Benchtop fluid and air manifolds on analytical instruments use 4 mm PU tube and M5 ports; the tee adds a sampling or purge branch mid-run without disturbing the main line.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D the Right Part?
Dia 4 is the floor of the PEB M5 ladder - only PEB6M5 sits above it, for Dia 6 tube where a little more bore helps short feed lines to small actuators. If you can step the port up, PEB4-01 keeps the Dia 4 tube but moves to a 1/8 PT thread, which carries the Dia 4 to Dia 10 range. A plain PE union tee is the right choice when the branch has no thread at all.
Tube OD must match exactly: this tee grips 4 mm tube and will not seal or hold 1/4 in (6.35 mm) tube. Match the M5 thread to instrument-style ports on mini cylinders, grippers and sensors; larger PT ports need a 01, 02 or 03 code instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D FAQ
It is a male branch tee for Dia 4 mm tube with an M5x0.8 male thread (PT sealing standard). Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Tubing is soft nylon or polyurethane, standard colour black (D suffix).
No. AirTAC ships threaded PEB fittings with sealant pre-applied on the PT threads, but the M5 size is sealed with a gasket instead, so the PEB4M5D screws into an M5x0.8 port without tape. Keep the gasket seat clean and do not overtighten the brass stud into an aluminium or plastic port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB4M5D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.