Airtac PEB T-Shaped Straight Thread Tee Connector PEB601
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB601 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB601
The PEB601 is an AirTAC male branch tee, the fitting you reach for when a 90 degree tap-off has to leave a straight tube run without cutting the line. It takes Dia 6 mm soft nylon or polyurethane tube into both legs and screws into a 1/8 in PT male port on the third leg. Both tube ends work the same one-touch way: push the tube fully home, the stainless spring gasket and chuck lock it against pressure, and the POM release button frees it again when you need to re-route.
This is the resin and brass profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a -20 to +70 C window. The body is PBT with a brass male stud, the guide is aluminium alloy and the O-ring is NBR. AirTAC ships the thread with sealant already applied, so a layer of PTFE tape on top is not needed.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB601 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB601 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB601
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB601 Is Used
Vacuum generator tap-off
Screwing into the vacuum port of a compact ejector on a packaging line, with 6 mm tube carrying the exhaust away at 90 degrees to the supply run.
Sensor branch on a bottling skid
Adding a pressure-switch leg off a 6 mm main feed to the filler heads, where the stud thread lands directly on the switch port without a separate adapter.
Second actuator on a palletizer head
Branching supply from an existing Dia 6 line to a small clamp cylinder, so one solenoid outlet serves both motions without a manifold block.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB601 the Right Part?
At the 1/8 in thread step on the PEB ladder this sits between PEB401 (Dia 4 tube) and PEB801 (Dia 8 tube). Stepping down to Dia 4 buys routing freedom in cramped cabinets but halves the bore, which shows on longer runs; stepping up to Dia 8 feeds actuators with real volume demand. The same Dia 6 tube also exists on PEB602 with a 1/4 in thread if the port you are filling is larger. Do not mix bore and port: a Dia 6 fitting will not seal on 1/4 in (6.35 mm) tube, only on true 6 mm OD.
Choose a branch tee (PEB) over a run tee (PED) when the take-off should sit at 90 degrees to the through-flow; if the branch must line up with one leg instead, PED is the shape you want.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB601 FAQ
Tube: Dia 6 mm soft nylon or polyurethane. Thread: 1/8 in PT male, supplied with sealant. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Construction: PBT body, brass stud, POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring.
In AirTAC's naming, PEB puts the threaded leg at 90 degrees to the tube path, so the branch leaves sideways while the main tube run continues straight through. PED, the male run tee, arranges the port so the flow path reads more like a line with a leg in the run direction. Pick PEB when you want the tap-off physically clear of the straight run, for example where a sensor or secondary actuator hangs off to one side. Both use the same one-touch grip and the same 0-1.0 MPa resin-profile ratings.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB601
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.