Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D
The PEB601D is an AirTAC PEB male branch tee: a push-in fitting that takes a single Dia 6 mm tube into its chuck and splits the flow through two 1/8" PT male threaded outlets set at 90 degrees to the tube axis. Push the tube in and the stainless spring gasket grips it; press the release ring and it slides free. The male stud arrives with sealant already on the thread, so it screws straight into a port without extra tape or paste.
This is the resin and brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa, vacuum down to -750 mmHg, proof pressure 1.5 MPa, and a service window of -20 to +70 C with soft nylon or polyurethane tubing. The D suffix makes this part genuinely black - on PEB series the body itself is recoloured, not just the POM release button as on the PC and POC straights - so the branch tee reads as part of a black-fitted machine rather than a grey add-on.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D Is Used
Pick-and-place gripper feed
On an EPSON or FANUC robot end-of-arm tooling, the PEB601D splits a single Dia 6 mm supply drop into two 1/8" threaded legs feeding gripper valves on either side of the wrist, keeping the branch inside the arm's tight envelope.
Vacuum ejector branch on a pick station
A vacuum generator drawing down to -750 mmHg can share its supply through this branch tee: the Dia 6 mm tube carries the feed while one 1/8" stud serves the ejector and the other serves the cup-pressure sensor tap.
Pilot-air takeoff on a packaging machine valve island
Where a SMC-style valve island offers only one spare 1/8" PT pilot port, the PEB601D branches it in two, letting a black-coloured fitting disappear visually against machine pipework while feeding a second function.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D the Right Part?
Both neighbours at the same 1/8" thread exist: the PEB401 steps down to Dia 4 mm tube for light pilot-air branches and compact sensor feeds, while the PEB801 steps up to Dia 8 mm when the branch must feed a cylinder at useful volume. Bore is what changes - flow capacity follows the tube, so oversize the branch rather than starve the actuator. If your port is larger, PEB602 pairs the same Dia 6 mm tube with a 1/4" PT stud instead.
Fit the branch where the geometry earns its keep: when one supply line must serve two destinations at right angles, a branch tee is neater than a union tee plus a male elbow. Check the tubing is exactly Dia 6 mm OD - a one-touch chuck sized for 6 mm will not seal on 1/4" (6.35 mm) hose, and the difference is easy to miss on an order sheet.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D FAQ
It is rated 0-1.0 MPa working pressure (0-10 kgf/cm2), tolerates vacuum to -750 mmHg (10 Torr), has a proof pressure of 1.5 MPa, and works from -20 to +70 C. This SKU accepts Dia 6 mm soft nylon or polyurethane tubing on a 1/8" PT male thread.
No. AirTAC ships the male PT stud with sealant already applied to the thread, so it seals on assembly; the M5 sizes in this catalogue instead use a sealing gasket. Simply check the port threads are clean and torque the brass stud home - over-wrapping tape on a pre-coated thread can push debris into the valve seat.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB601D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.