Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S
SUS304 stainless variant (-S)The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S
The PEB602-S is an AirTAC PEB male branch tee: a Dia 6 mm tube branch joins a 1/4 in PT male port at 90 degrees, so one supply line can feed two destinations without an extra elbow. Push the 6 mm tube into the branch port and the internal chuck grips it; press the release ring and it slides straight back out. On this -S version the stud that screws into your port is SUS304 stainless steel, while the PBT body and POM release button stay exactly as the standard part - AirTAC keeps the same dimensions, so it is a direct swap for a corroded brass PEB602.
This is the resin one-touch spec, not the metal BP line: working pressure 0-1.0 MPa, vacuum to -750 mmHg, proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. The threaded stud arrives with sealant already applied, and a hex on the stud lets you torque the body angle before the tube goes in.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S Is Used
Indexing table branch feed
On a rotary indexing table, one 1/4 in PT riser can tee the Dia 6 branch that charges the clamp cylinder at each station, with the SUS304 stud resisting coolant splash around the dial plate.
Packaging machine drop leg
A cartoning machine's manifold riser can feed a Dia 6 drop to the glue-head sensor jet, the tee's angled branch clearing the guard rail where a straight fitting would foul.
Plating-line rinse station
At an electroplating rinse bench, acid mist corrodes brass fast - the stainless stud keeps the 1/4 in port seal intact while the Dia 6 branch feeds the air-purge nozzle.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S the Right Part?
Within the PEB ladder at 1/4 in thread, the neighbouring branch sizes are PEB402 (Dia 4) below and PEB802 (Dia 8) above. Stepping down to Dia 4 buys routing space and a smaller bend radius but halves the bore your branch can breathe through; stepping up to Dia 8 suits longer branch runs or a bigger actuator. If you need the same split without a threaded port, the PE606 union tee is the tube-to-tube alternative. Remember the tube must match the nominal OD exactly - a Dia 6 chuck will not seal on 1/4 in (6.35 mm) imperial tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure to -750 mmHg, proof pressure 1.5 MPa, operating temperature -20 to +70 C. The part joins Dia 6 mm soft nylon or polyurethane tube to a 1/4 in PT male thread, and the stud is SUS304 stainless steel on this -S variant.
No. For the PEB family AirTAC supplies only the stud in SUS304; the tee body stays PBT with a POM release button and NBR O-ring. Pressures, temperatures and dimensions are identical to the standard PEB602, so you gain corrosion resistance at the port seal without re-rating or re-drawing anything.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB602-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.