Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S
SUS304 stainless variant (-S)The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S
The PEB602D-S is an AirTAC PEB male branch tee from the resin one-touch range: a straight tube run with a male branch at 90 degrees, so one 1/4in PT port can feed two Dia 6 mm lines. Push the soft nylon or polyurethane tube into the branch port until it bottoms, and the internal chuck grips it; press the POM release ring to let it go. The D suffix makes the body black, which on the PEB series means the whole body, not just the button.
The -S code fits this family differently than on the PC straight connectors: here the body stays glass-reinforced PBT and it is the threaded STUD that is SUS304. That protects the male thread - the part that siezes and corrodes inside manifold ports - without changing the shape or a single rating. The part still works at 0-1.0 MPa, proof pressure 1.5 MPa, down to -750 mmHg vacuum, and -20 to +70 C. The 1/4in thread arrives with sealant already applied, so it seals straight into a PT-tapped port.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S Is Used
Packaging machine vacuum feed
Tee a Dia 6 mm suction-cup drop off a 1/4in manifold port on a carton erecting line, with the SUS304 stud standing up to repeated port removal on changeovers.
Machining centre air blast
Branch a Dia 6 mm chip-blow-off nozzle line from a 1/4in PT port on a CNC enclosure, keeping the branch at 90 degrees to the main run.
Palletizer gripper split
Feed two Dia 6 mm gripper-cylinder lines from a single 1/4in port on a robotic palletizing cell, using the branch thread as the supply side.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S the Right Part?
On the 1/4in row of the PEB ladder you can step down to PEB402-S (Dia 4) or up to PEB802-S (Dia 8). Dropping to Dia 4 suits light pilot and signal drops off the same port; stepping to Dia 8 gives a larger bore for actuators with real air demand, since capacity follows the tube bore. If your run continues in tube and the actuator hangs off the tee instead, the PED run tee puts the thread in the line and the branch out at 90 degrees - the opposite arrangement to this part.
Tube OD must match exactly: a Dia 6 chuck will not seal or hold 1/4in (6.35 mm) hose. Where the feed passes through a panel wall rather than branching off a port, the PM bulkhead union or PLM bulkhead male elbow is the shape to ask for instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum to -750 mmHg (10 Torr), temperature -20 to +70 C. The fitting accepts Dia 6 mm soft nylon or polyurethane tube in each run port and has a 1/4in PT male branch thread. The body is black PBT (D suffix) and the threaded stud is SUS304; the -S code does not change any pressure or temperature figure.
It depends on which leg carries the threaded supply. On the PEB602D-S the male thread sits on the 90-degree branch, so the tube run passes straight through and the air turns out of the line. On a PED the thread is in the straight run and the second tube port is the branch. Pick PEB when the port on the machine is the source and two tube lines continue onward; pick PED when the supply travels through the fitting and one drop leaves at right angles.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB602D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.