Airtac PEB T-Shaped Straight Thread Tee Connector PEB603
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB603 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB603
The PEB603 is an AirTAC PEB male branch tee: a three-way one-touch fitting that takes a Dia 6 mm tube on both tube ports and screws into a 3/8in PT male thread. Unlike a run tee, the branch outlet sits at 90 degrees to the through-flow path, so you can split a supply line sideways without twisting the tubing to make it reach.
This is the resin/brass one-touch profile: working pressure 0-1.0 MPa, vacuum to -750 mmHg, proof pressure 1.5 MPa, temperature -20 to +70 C. Push the tube home and the internal chuck grips it; press the POM release ring and it slides free. The threaded stud ships with sealant already applied, and the body is PBT over a brass stud.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB603 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB603 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB603
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB603 Is Used
Valve manifold branch take-off
Screws onto a spare 3/8in PT port on a solenoid valve manifold and branches a 6 mm feed line sideways to a downstream actuator without re-plumbing the main run.
Packaging machine drop leg
On a form-fill-seal or cartoning machine, the 90 degree branch lets a 6 mm vacuum or blow-off line drop vertically while the supply continues straight through the tee.
Jig and fixture clamping circuit
Mounted at a welding or assembly fixture, it splits one regulated supply into two 6 mm clamp cylinder circuits, with the resin body resisting coolant splash from -20 to 70 C.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB603 the Right Part?
On the 3/8in branch-tee ladder you are at the bottom of the tube range: PEB803 steps you up to Dia 8 tube on the same 3/8in port if the line later carries more demand. If the port itself is the constraint, PEB602 keeps the Dia 6 tube but drops the thread to 1/4in PT for smaller manifold ports. Dia 6 means exactly 6 mm OD: a 6 mm fitting will not seal on 1/4in (6.35 mm) tube, and vice versa.
If the tee must pass through a panel wall instead of screwing onto a port, the PMF bulkhead connector with a locknut is the shape to look at rather than forcing this one in. Do not add PTFE tape over the factory sealant; the thread arrives ready to assemble.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB603 FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Size: Dia 6 mm tube OD on both tube ports with a 3/8in PT male thread. Applicable tubing is soft nylon or polyurethane.
No. AirTAC applies sealant to the male thread at the factory, so it can be assembled straight into a PT port. Because PT is a taper thread, hand-tighten then snug it - on the one-touch side just push the 6 mm tube fully home until it stops; the chuck inside grips it and the release ring frees it later without disturbing the thread seal.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB603
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.