Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5
The PEB6M5 is an AirTAC PEB male branch tee: a run of Dia 6 mm soft nylon or polyurethane tube passes straight through the body, and a 90-degree branch with a male M5x0.8 thread takes off at right angles from the same body. It is the natural fitting when you want to tap a signal or pilot line off a main run without adding a separate union and elbow. Push the tube into the port until it bottoms out and the internal chuck grips the OD; press the POM release ring to free it. Unlike the larger threaded sizes, the M5 port is not delivered with pre-applied sealant - it seals with a gasket on the seat, so no tape or dope is needed and none should be added.
This is a resin/brass one-touch part, so it carries the standard resin rating, not the metal BPC line: 0-1.0 MPa (0-10 kgf/cm2) working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and a -20 to +70 C window. The body is PBT with a brass male stud, a POM button and chuck, an aluminium-alloy guide, a stainless spring gasket and an NBR O-ring. Grey is standard; a D suffix on this family changes the body to black.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5 Is Used
Branching off an M5 valve manifold
Take a 6 mm pilot line at right angles from the M5 outlet of a solenoid manifold on a small pick-and-place unit, keeping the main tube run unbroken through the tee.
Lab and small analyser pneumatics
Feed a Dia 6 purge or actuation line from an M5 port on compact lab bench equipment, where the gasket-sealed M5 seat avoids thread tape near sensitive optics.
Packaging machine sensor air feeds
Tap a clean 6 mm supply off a main run to power small air-jet or rejection blow-offs on a horizontal flow-wrapper, using the branch outlet without a second fitting.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5 the Right Part?
On the M5 row of the PEB ladder only two tube sizes exist: Dia 4 and Dia 6. Step down is PEB4M5, which lightens the branch line for very small pilot or sensor feeds; step up from here means leaving M5 entirely, because Dia 8 is not offered on M5 for this prefix. If you need an 8 mm branch off a run, move to PEB801 with its 1/8 in thread. On the same Dia 6 tube, the thread neighbour is PEB601 (1/8 in) - useful when the port is a standard PT tapping rather than a compact M5 manifold port. On the M5 version there is no released larger thread above it; M5 is the smallest entry on the PEB ladder.
Match the tube exactly: a Dia 6 one-touch chuck will not seal or hold 1/4 in (6.35 mm) tube, and forcing the wrong OD is the most common cause of a weeping push-fit. If the branch has to pass through a panel instead of standing off a run, the PMF bulkhead connector is the right shape, not this tee.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5 FAQ
Tube size Dia 6 mm, branch thread M5x0.8 (gasket sealed, PT series family). Working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Suitable tubing is soft nylon or polyurethane in Dia 6 OD only. It is a resin/brass one-touch fitting with POM chuck and button, PBT body, brass stud, stainless spring gasket and NBR O-ring.
No. AirTAC's interface table allows M5 on the PEB prefix for Dia 4 and Dia 6 tube only, so the PEB6M5 is already the larger of the two M5 options. For an 8 mm branch you need the 1/8 in threaded PEB801, and Dia 4 branch lines use PEB4M5. Always match the tube OD to the fitting exactly - the chuck grips one size and one size only.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.