Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S
SUS304 stainless variant (-S)The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S
The PEB6M5-S is an AirTAC PEB male branch tee in the SUS304-stud variant, joining Dia 6 mm soft nylon or polyurethane tube to an M5x0.8 male thread. As a branch tee, the threaded outlet sits at 90 degrees off a straight tube run, and the two through legs stay inline - a different flow geometry from the PED run tee, where the third way sits in the main flow path. Connection is genuinely one-touch: push the tube home and the internal chuck grips it, press the POM release ring and the tube frees again.
This SKU runs on the resin and brass spec profile: 0-1.0 MPa working pressure, -750 mmHg vacuum capability, 1.5 MPa proof pressure and -20 to +70 C. The -S suffix replaces the brass stud with SUS304 while the body itself stays PBT, so ratings and dimension tables match the standard grey part exactly. One detail specific to this size: M5 ports do not carry pre-applied thread sealant the way the larger tapered threads do - they seal through a gasket, so no thread tape goes on the stud.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S Is Used
M5 pilot port takeoff
Branch a Dia 6 signal line off the M5 pilot or gauge port of a compact solenoid valve stack on a packaging machine, leaving the main flow path undisturbed.
Vacuum gripper sensing
Tee a Dia 6 pressure-switch tube off the M5 port of a small ejector line so a pick-and-place robot can confirm vacuum levels down to -750 mmHg at the gripper.
Lean fixture air drop
Feed a bench-mounted air nozzle or part-counter cylinder inside a workstation fixture, teeing off an M5 port where a 1/8 in threaded tee would be too bulky.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S the Right Part?
On the PEB M5 ladder only Dia 4 and Dia 6 exist, so PEB6M5-S is the top of this thread's range - there is no Dia 8 M5 branch tee. Step down to PEB4M5-S for a lighter 4 mm sensor or signal line, or step up to the 1/8 in PEB601-S if the run legs need Dia 8, Dia 10 or Dia 12 tube. The tube must measure exactly 6 mm OD: a 1/4 in tube at 6.35 mm will not seal in the chuck. Pick this branch tee over a union tee when the supply has to come off the port itself rather than from a joint partway along the tube run.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum capability to -750 mmHg (10 Torr), and a temperature range of -20 to +70 C. This SKU joins Dia 6 mm soft nylon or polyurethane tube to an M5x0.8 male thread, supplied as the SUS304-stud variant on a PBT body.
No. On the PEB family the -S option swaps the brass stud for SUS304 only; the body remains PBT and every pressure, vacuum, temperature and dimensional figure is identical to the standard grey part. A solid stainless body is offered only on the -S versions of the PC and POC straight connectors, not on the tee and elbow families.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB6M5-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.