Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D
The PEB802D is an AirTAC PEB male branch tee, the fitting that splits one incoming line into two outlets set at 90 degrees to each other. This version joins Dia 8mm tubing on the two push-in legs and screws into a 1/4in PT male port. The D suffix means the body arrives in black rather than the standard grey, and on the PEB family that colour change applies to the fitting body itself, not just the release button.
Push the soft nylon or polyurethane tube into either leg and the internal chuck grips it immediately; press the POM release ring and the tube slides free again. The 1/4in threaded stud arrives with sealant already applied, so no extra tape or paste is needed on the port. This is the resin one-touch profile: 0 to 1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure, -20 to +70 C, with a brass stud and stainless spring gasket behind a PBT body.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D Is Used
Valve manifold branch take-off
Screws straight into the spare 1/4in port of a solenoid valve manifold on a packaging machine, branching an 8mm feed to a secondary clamp cylinder without a separate junction block.
Conveyor gate diverters
On sorting conveyors with pneumatic pusher gates, the branch tee splits a single 8mm supply drop into the gate cylinder circuit and a position-sensing line, both released tool-free during changeover.
Rotary indexing table feeds
At a rotary indexing assembly table, the 90-degree branch keeps the 8mm drop to each station's gripper cylinder routed tight against the machine frame, and the black body blends with dark anodised guards.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D the Right Part?
Within the 1/4in thread row for PEB, the neighbouring tube sizes are Dia 6mm below (PEB602) and Dia 10mm above (PEB1002). Stepping down to 6mm suits lighter actuators and shorter runs, while 10mm carries noticeably more air to cylinders with bigger bores. On the thread side, PEB801 drops this same 8mm tee to a 1/8in port and PEB803 raises it to 3/8in. If your drawing actually needs the third port in line with the run rather than branching at 90 degrees, you want the PED run tee instead - the two are easy to confuse on a circuit print.
Tube OD must match exactly: a Dia 8mm chuck will not seal on 1/4in or 5/16in imperial tube, so check the old tubing before ordering.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D FAQ
The PEB802D is a male branch tee taking Dia 8mm tube on its push-in legs with a 1/4in PT male thread on the stud. Working pressure is 0 to 1.0 MPa (0 to 10 kgf/cm2), it withstands -750 mmHg (10 Torr) vacuum, proof pressure is 1.5 MPa, and the temperature range is -20 to +70 C. Use soft nylon or polyurethane tubing. The threaded stud carries factory-applied sealant.
On a PEB branch tee, the third port exits at 90 degrees off the straight run of the line, which is what you need when tee-ing a drop off a main circuit. On a PED run tee, all three ports sit in a T where one leg continues the run through the fitting. They look similar on a parts list but produce different piping geometry, so match the fitting to the drawing before ordering.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.