Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S
SUS304 stainless variant (-S)The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S
The PEB802D-S is an AirTAC PEB male branch tee, the fitting you use when one 1/4in PT port has to feed two Dia 8 mm lines at roughly 90 degrees to each other. The male stud screws into the port while both tube ends push straight in: the chuck inside each socket grips the tubing on insertion, and pressing the release ring frees it again without tools. The -S suffix puts a SUS304 stainless stud in place of the standard brass one, so the threads that sit in a damp or frequently washed port resist corrosion.
This is part of the resin one-touch family, so it is rated 0 to 1.0 MPa (0 to 10 kgf/cm2), handles -750 mmHg vacuum, and carries a proof pressure of 1.5 MPa over a temperature window of -20 to +70 C. The tee body is PBT with the black finish the D suffix signals, and the release button and chuck are POM. Note that the stainless is on the stud only, not the whole body. Threaded studs arrive with sealant already applied, so no extra tape or compound is needed on the 1/4in thread.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S Is Used
Brewery CIP rinse branch
Branching a caustic rinse feed off the main Dia 8 supply run to a spray bar on a filling-head rinse skid, where the stainless stud stands up to repeated wash-down.
Poultry-line gripper cylinders
Feeding a pair of Dia 8 gripper cylinders from one 1/4in PT port on a header at a wash-down section of a poultry processing conveyor.
Marine deck hatch actuator
Splitting the supply at a 1/4in PT port to run both the hatch cylinder and its position-sensing line on a boat deck, where salt air would corrode a plain brass stud.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S the Right Part?
On the PEB ladder at 1/4in PT, the neighbours either side of Dia 8 are PEB602 (Dia 6) and PEB1002 (Dia 10). Stepping down to 6 mm trims the bore and suits lighter-feeding runs to small actuators; stepping up to 10 mm opens the bore where a longer branch or a bigger cylinder needs less restriction. Capacity scales with the tube bore, not with any published flow figure. If you need a three-way join with all branches on tubing instead of a port thread, that is the PE union tee, not PEB.
Check two things before ordering. First, the tube must match exactly: this socket grips Dia 8 mm outside diameter only, and will not seal 1/4 inch (6.35 mm) tube or Dia 10. Second, the D in the code means a black body; order the plain PEB802-S if grey is wanted.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), proof pressure 1.5 MPa, vacuum to -750 mmHg (10 Torr), temperature -20 to +70 C. The fitting joins Dia 8 mm outside-diameter soft nylon or polyurethane tube to a 1/4in PT male thread, with a SUS304 stud and a black PBT body.
No, and the coincidence trips up many buyers. The 1/4in figure in the code is the PT thread only. The collet is cut for Dia 8 mm outside diameter, which is about 5/16 inch, so a 6.35 mm tube will not grip or seal. Use the correct nominal tube, or move to the PEB6 size if your run is genuinely 6 mm.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB802D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.