Airtac PEB T-Shaped Straight Thread Tee Connector PEB804
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB804 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB804
The PEB804 is an AirTAC PEB series one-touch male branch tee. It joins Dia 8 mm soft nylon or polyurethane tube to a 1/2 inch PT male thread and puts the tube outlet at 90 degrees to the run, so a branch line can leave a straight main run without an extra elbow. Push the tube home and the internal chuck grips it; press the POM release ring and the tube frees again. The 1/2in stud is brass and arrives with sealant already applied to the thread.
This belongs to the resin and brass one-touch family, not the metal BPC line: working pressure 0 to 1.0 MPa, vacuum down to -750 mmHg, proof pressure 1.5 MPa and a temperature window of -20 to +70 C. The body is PBT with a POM button and chuck and an NBR seal. Grey is standard; order PEB804D if you need the black body build for this series.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB804 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB804 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB804
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB804 Is Used
Packaging machine header branch
Screwed into the 1/2in PT tapping of a carton-forming machine's main air header, splitting a Dia 8 branch off to feed the rotary pick-and-place actuators without adding a separate elbow.
Bottling line gate cylinders
A branch tee in the end cap of a bottling conveyor's air main, running Dia 8 polyurethane drops down to the gate and stopper cylinders at each lane while the main continues straight through.
Spinning frame valve bank feed
The 1/2in PT stud lands directly on the solenoid valve manifold inlet of a textile spinning frame, with the Dia 8 outlet carrying air out to the jet nozzles along the machine length.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB804 the Right Part?
On a 1/2in PT thread the PEB ladder runs Dia 8, 10 and 12, so PEB804 is the smallest branch tee that exists for a 1/2in port; the next one up is PEB1004 for Dia 10 tube. If your port is 3/8in instead, PEB803 carries the same Dia 8 tube one thread size down, and Dia 6 becomes available there as PEB603. Tube outside diameter must match exactly - a Dia 8 chuck will not hold 5/16in tube. Where the branch has to pass through a panel wall rather than off a run, a PMF bulkhead connector or PLM bulkhead male elbow is the shape to use instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB804 FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. The fitting takes Dia 8 mm soft nylon or polyurethane tube on the tube side and a 1/2 inch PT male thread on the stud.
On the PEB804 the Dia 8 tube outlet sits at 90 degrees to the run, so the branch leaves sideways off a straight main line. A PED run tee in the same size puts the branch in line with the run instead. Both share the 1/2in PT thread and identical ratings, so the choice is purely the piping geometry on your machine.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB804
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.