Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S
The PED1001-S is an AirTAC one-touch male run tee in the Dia 10 tube size with a 1/8in PT male branch. On a run tee the threaded stud sits in line with the flow path, so the main Dia 10 air line passes straight through while the 1/8in port branches off at 90 degrees from the same body. On this -S variant the stud is SUS304 stainless steel; the body stays PBT with a POM chuck, aluminium-alloy guide, stainless spring gasket and NBR seal.
Connection is push-to-connect: push the Dia 10 tube fully home into each run end and the chuck grips it against the spring gasket; press the release ring to free it. This is the resin spec profile, rated 0-1.0 MPa (0-10 kgf/cm2) working pressure, 1.5 MPa proof, -750 mmHg vacuum and -20 to +70 C, with soft nylon or PU tubing. The 1/8in thread arrives with sealant already applied.
Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S Is Used
Indexing table on a packaging line
Splice the PED1001-S into a Dia 10 trunk run feeding a rotary indexing table so the 1/8in stud drops a branch straight to the clamp cylinder port without a second elbow.
Pressure monitoring on a screen printer
Tee the Dia 10 squeegee air supply mid-run and use the 1/8in male branch to carry a pressure switch, keeping the main line unbroken through the machine frame.
Gripper plumbing in an electronics cell
On a pick-and-place gripper manifold, the SUS304 stud threads into the fixture plate port while both Dia 10 run ends continue the supply line to the wrist actuators.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S the Right Part?
Step down to PED801 for a Dia 8 line on the same 1/8in thread - the body shrinks and flow capacity drops with the narrower bore. PED1001 is the largest tube size AirTAC makes on the 1/8in branch for this prefix, so to go above Dia 10 you change the thread: PED1002 moves to 1/4in, and PED1202 covers Dia 12 tube. Match the stud to the receiving port, never the tube.
If the branch must sit at a corner rather than mid-run, the PEB male branch tee is the offset alternative; if the branch has to pass through a panel wall, PM bulkhead fittings take a locknut instead. Keep tubing OD exact - a Dia 10 fitting will not seal on 3/8in or 12mm tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum to -750 mmHg (10 Torr), temperature -20 to +70 C. Both run ends take Dia 10 mm soft nylon or polyurethane tube; the branch is a 1/8in PT male thread on a SUS304 stainless stud set into a PBT body. This is the standard resin one-touch profile - the -S changes the stud material only, not any rating.
On this PED run tee the threaded stud lies on the straight-through flow axis, so the Dia 10 line continues in a straight line and the 1/8in port taps off at 90 degrees - ideal for teeing a gauge or valve off a long run. On the PEB branch tee the thread sits offset, which suits corner plumbing. Both use the same push-fit chuck, and neither needs tools beyond a wrench on the stud.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED1001-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.