Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S
The PED1001D-S is AirTAC's male run tee in the Dia 10 tube size with a 1/8in PT male thread. A run tee differs from a branch tee in one practical way: the main line passes straight through the body, and the threaded male port takes off at 90 degrees from that run. Use it where you want to feed a component from the middle of an air line without breaking the flow to everything downstream.
One-touch action: push the Dia 10 soft nylon or PU tube into the chuck until it seats, and the stainless spring gasket and NBR O-ring seal around it; press the release ring to let it go. The -S suffix makes the threaded stud SUS304 while the tee body itself stays PBT in the black D colour - so this is the right pick when the connection point needs corrosion resistance at the port, not a full stainless body. Ratings follow the standard resin profile: 0-1.0 MPa, -750 mmHg vacuum, 1.5 MPa proof, -20 to +70 C.
Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S Is Used
Bottling line rinser manifold
On a bottle-rinsing conveyor, the Dia 10 trunk can run straight through the PED body while the 1/8in male port drops air to a nearby blow-off or gate cylinder, keeping the main flow uninterrupted for the stations beyond.
Rotary indexing table circuit
A indexing dial machine routes its supply through the run of the tee to the next rotary union, and the threaded stud taps a controlled branch to the clamp cylinder at that station - one part does both jobs.
Lab autoclave aux supply
Where a steam-rich or wash-prone environment attacks plated brass studs, the SUS304 male thread on this tee resists rust at the port, while the PBT body suits the -20 to +70 C ambient of a laboratory service line.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S the Right Part?
On the 1/8in thread ladder for PED, Dia 10 is the top of the range - the sizes below it are Dia 4, Dia 6 and Dia 8 (PED801D-S is the one step down). Stepping from Dia 8 to Dia 10 roughly doubles the bore area, so this size carries the volume for the trunk portion of a run rather than a drop to a small valve. If you need Dia 12 tube, 1/8in will not take you there on this prefix; the path up is PED1002D-S, the same Dia 10 tee on a 1/4in PT thread, which also opens Dia 12 further along its ladder.
Match the thread to the port, not to hope: 1/8in PT is common on compact cylinders, small FRL outlets and manifold branch ports. Tubing must be Dia 10 exactly - a Dia 10 fitting will neither grip 3/8in hose nor seal on 12mm tube, so check the tube marking before ordering. If the port is on a panel wall rather than an open manifold, the PMF bulkhead connector is the shape to compare against this run tee.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2); vacuum down to -750 mmHg (10 Torr); proof pressure 1.5 MPa; temperature -20 to +70 C. It joins Dia 10 mm soft nylon or polyurethane tube to a 1/8in PT male thread. The body is black PBT and the -S suffix makes the threaded stud SUS304; the internal chuck seal is a stainless spring gasket with an NBR O-ring. Release button and chuck are POM, guide is aluminium alloy.
No, and it matters when writing a spec. On the PED family, the -S option is a SUS304 stud only - the tee body, button and chuck remain POM/PBT construction. If your wash-down or marine environment needs an all-stainless wetted body, the straight PC and POC connectors are the parts where -S makes the body itself SUS304. Either way the pressure, temperature and size limits are identical to the standard version.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED1001D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.