Airtac PED T-Shaped Side Thread Tee Fitting PED1002D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED1002D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED1002D
The PED1002D is an AirTAC PED male run tee, a three-way one-touch fitting with two push-in tube ports arranged in a straight 10 mm line and a third push-in port branching at 90 degrees, all closing onto a 1/4in PT male thread. It belongs to the resin and brass one-touch range: push soft nylon or polyurethane tube into each port until it bottoms out, the stainless spring gasket and POM chuck grip it, and pressing the release ring frees it again.
The ratings follow the standard resin profile, not the metal BPC line: 0 to 1.0 MPa working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70 C temperature. The 1/4in thread arrives with sealant already applied, so it seals straight into a PT port without extra tape. The D suffix gives the whole body a black finish rather than the standard grey.
Airtac PED T-Shaped Side Thread Tee Fitting PED1002D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED1002D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED1002D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED1002D Is Used
Main air line tee-off
Splice a 10 mm cylinder drop at 90 degrees from an unbroken 10 mm supply run feeding a punch press, keeping the main flow path straight through the fitting.
Vacuum pick-and-place manifold
Branch three 10 mm vacuum lines off one point on a cartesian gantry for suction-cup handling of flat sheet; the -750 mmHg rating covers ejector-fed circuits.
Valve manifold distribution
Take a 1/4in valve-manifold outlet straight into a run tee that continues a 10 mm line onward to a second actuator on a packaging carousel.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED1002D the Right Part?
On the same 1/4in thread, the PED ladder steps through 4, 6, 8, 10 and 12 mm, so PED802 is the size down and PED1202 is the size up from this Dia 10 part. Stepping to Dia 12 raises flow capacity through the wider bore for longer main runs; stepping to Dia 8 suits shorter drops where the downstream cylinder consumes less air. If you need a 3/8in port instead, the PED range supports Dia 10 on that thread too, but never order a 1/2in with Dia 10 expectation checked against this family - verify the ladder before committing. Match the OD exactly: a Dia 10 port will not seal on 3/8in tube.
Choose a run tee rather than the PEB branch tee when the supply must flow straight through the fitting and the branch leaves at right angles, such as teeing a cylinder drop off an unbroken air main. For feeding through a panel wall with a locknut, the PM bulkhead or PLM bulkhead male elbow is the right shape instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED1002D FAQ
It is an AirTAC PED male run tee for Dia 10 mm soft nylon or polyurethane tube with a 1/4in PT male thread, black body. Working pressure 0 to 1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. Release button and chuck are POM, guide is aluminium alloy, spring gasket stainless, O-ring NBR, stud brass, body PBT.
No. Every PED port in one part number takes the same single tube OD, here exactly 10 mm - a 12 mm or 8 mm tube will not seat on the chuck. If the branch must be a different diameter than the run, use a different-diameter family part such as the PEG or PEW tee. For a different thread on the same Dia 10 tube, the PED ladder also offers 1/8in and 3/8in, but always confirm the size appears on the PED row before ordering.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED1002D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.