Airtac PED T-Shaped Side Thread Tee Fitting PED1003D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED1003D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED1003D
The PED1003D is an AirTAC male run tee from the PED one-touch family, supplied in black (the D suffix). It carries a 3/8in PT male thread in the run with two Dia 10 mm tube ports, so a single threaded port on a valve, manifold or FRL outlet can feed a straight-through line and a 90 degree branch without extra junction fittings.
This is the resin and brass profile, not the metal BPC line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. To connect, push soft nylon or PU tube into the port until it bottoms; the stainless spring gasket and chuck grip the tube, and pressing the POM release ring frees it again. The thread arrives with sealant already applied, so no extra tape or paste is needed.
Airtac PED T-Shaped Side Thread Tee Fitting PED1003D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED1003D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED1003D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED1003D Is Used
Distribution along a packaging conveyor rail
A 3/8in thread at the FRL outlet continues the main Dia 10 supply straight down the rail while the branch port feeds a gripper or gate cylinder at one station, using one fitting instead of a tee plus a connector.
Air drops in a woodworking shop
On a compressed air ring main serving saws and sanders, the run tee taps a Dia 10 branch off the 3/8in through-line to feed a bench regulator, keeping the main flow uninterrupted.
Retooling a pneumatic press control panel
Where a valve manifold carries a 3/8in PT outlet, this black run tee splits supply to a counterbalance circuit while the straight run continues to a downstream actuator, all push-fit for fast servicing.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED1003D the Right Part?
Within the PED ladder, stepping from this Dia 10 tee down to PED803D drops the bore, which increases velocity and pressure drop on the same flow demand and suits shorter branch runs. Stepping up to PED1203D adds bore for longer lines or higher draw at the same 3/8in thread. If the port is smaller, PED1002 in 1/4in keeps the 10 mm tube; for a 1/2in port, PED1004 also accepts Dia 10. Every tube port takes Dia 10 OD tubing only - a 3/8in imperial tube will not seal in a 10 mm port, so match the OD exactly.
A run tee is the right shape when the flow should continue straight past the branch, for example along a machine rail. If you need the threaded port turned 90 degrees instead, the PEB male branch tee points the thread sideways; PL gives a two-way elbow rather than a tee.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED1003D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2); vacuum to -750 mmHg (10 Torr); proof pressure 1.5 MPa; operating temperature -20 to +70 C. Tube ports: Dia 10 mm OD (soft nylon or polyurethane). Thread: 3/8in PT male, supplied with sealant on the thread. Finish: black, per the D suffix. The thread standard on this catalogue is PT throughout.
On the PED family the D suffix makes the whole fitting black, not just the release button as on the PC and POC connectors, so it is easy to colour-code a machine circuit. Use soft nylon or polyurethane tube with a true 10 mm outside diameter; the chuck grips the OD, so any oversize or imperial tube will not seat past the spring gasket and will leak or blow off.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED1003D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.