Airtac PED T-Shaped Side Thread Tee Fitting PED1202D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED1202D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED1202D
The AirTAC PED1202D is a resin-bodied male run tee from the PED family: two Dia 12 mm push-in sockets in a straight run, with a 1/4 inch PT male thread set in line with that run. That in-line thread is what separates a run tee from the PEB branch tee, where the male port stands off at 90 degrees - on a PED the threaded port sits on the axis, so the supply continues straight through while a take-off feeds a branch circuit. Tube pushes into each socket until the internal chuck grips it; pressing the release ring frees it again.
This is the resin and brass one-touch profile, not the metal BP line: 0-1.0 MPa working pressure, 1.5 MPa proof pressure, -750 mmHg vacuum, and a service range of -20 to +70 C with soft nylon or polyurethane tubing. The D suffix on a PED turns the body itself black, not just the release button, which suits panels and machines where grey fittings would stand out. The PBT body carries a brass stud and the thread arrives with sealant already applied, so it goes straight into the port.
Airtac PED T-Shaped Side Thread Tee Fitting PED1202D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED1202D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED1202D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED1202D Is Used
Bottling line air main take-off
On a bottling hall's ring main built from 12 mm nylon tube, the run tee taps a 1/4 inch port off the straight run to feed a local filter-regulator without breaking the header flow path.
Solenoid valve manifold supply
The 1/4 inch PT stud threads directly into the supply port of a five-port solenoid valve on a packaging machine, letting the 12 mm tube run be lifted off for valve replacement in seconds.
Conveyor guard blow-off circuit
Along a carton conveyor fitted with dust-blow nozzles, the in-line thread splits the 12 mm main so each zone gets its own branch feed, all in black to match the machine's dark guard work.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED1202D the Right Part?
Dia 12 is the top of the PED ladder on a 1/4 inch thread. Step down to PED1002 for Dia 10 tube and you gain a smaller, cheaper fitting for lighter branch lines; step up and there is nothing - Dia 12 is the largest tube this family takes, so a bigger main header needs hard piping or a different connection. On the thread side, note that 1/4 inch is actually the smallest port size a Dia 12 PED is offered in: the 1/8 inch and M5 versions stop at Dia 10, while PED1203 (3/8 inch) and PED1204 (1/2 inch) cover larger ports. Match the thread to the existing tapped hole and remember the tube must be exactly Dia 12 - a 10 mm or 1/2 inch tube will not seal in this socket.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED1202D FAQ
It is a one-touch male run tee joining Dia 12 mm tubing to a 1/4 inch PT male thread, in a black body. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), proof pressure is 1.5 MPa, and it holds vacuum down to -750 mmHg (10 Torr). Service temperature is -20 to +70 C with soft nylon or polyurethane tube. The PBT body carries a brass stud with pre-applied thread sealant.
Both have three ports, but on the PEB the male thread stands off at 90 degrees as a branch, while the PED places its 1/4 inch thread on the same axis as the tube run. Choose the PED when the supply should continue straight through the fitting and the threaded port is simply a tap-off point - for example feeding a valve from an in-line main - and the PEB when a right-angle outlet keeps the tube routing tight against a surface.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED1202D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.