Airtac PED T-Shaped Side Thread Tee Fitting PED804
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED804 is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED804
The PED804 is an AirTAC PED male run tee, a one-touch fitting whose main run passes straight through the body while a male 1/2 in PT thread projects at 90 degrees from the tee centre. It takes Dia 8 mm soft nylon or polyurethane tube on the push-in ports. To connect, push the tube home; an internal chuck grips it against the stainless spring gasket, and pressing the POM release ring frees it again.
This is the resin and brass one-touch line: 0 to 1.0 MPa working pressure, -750 mmHg vacuum capability, 1.5 MPa proof pressure, -20 to +70 C. The body is PBT with a brass stud, and the 1/2 in thread arrives with sealant already applied, so it seals into the port without extra tape. Note the distinction from a branch tee: on the PED run tee the air keeps a straight path along the run, which keeps restriction on the main line low.
Airtac PED T-Shaped Side Thread Tee Fitting PED804 Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED804 |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED804
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED804 Is Used
Manifold branch to a control valve
The 1/2 in PT male thread screws into a valve island supply port while the run carries 8 mm line onward, so the branch joins without a separate elbow.
Air drop along a conveyor frame
On a packaging conveyor, the run tee taps 8 mm tube off a straight trunk line at each station, with the thread pointing at the actuator it feeds.
Header line in a machine build
Machine builders use the straight-through run at a header end so the main 8 mm air route is not throttled at the point where a branch leaves.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED804 the Right Part?
On the 1/2 in thread, PED covers Dia 8, 10 and 12 mm tube, so Dia 8 is the smallest tube you can pair with this port size and the next step up is the PED1004 for Dia 10 mm. If your port is smaller, the same Dia 8 tube fits the PED803 on 3/8 in and the PED802 on 1/4 in, which is worth knowing when a manifold mixes port sizes. A Dia 8 fitting only holds 8 mm OD tube; it will not clamp 1/4 in or 5/16 in tube, so measure before ordering. Choose the run tee shape when the supply line should continue past the branch instead of turning, and choose a bulkhead union instead if you need to pass through a panel wall.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED804 FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature range of -20 to +70 C. This part accepts Dia 8 mm soft nylon or polyurethane tube on the one-touch ports and has a 1/2 in PT male thread, sealed on arrival. The body is PBT with a brass stud.
Both screw a male thread at 90 degrees off the tube line, but on the run tee the tube path continues straight through the fitting, while on a branch tee the geometry turns the flow at the branch. If your main line should keep a straight low-restriction path, stay with the PED; if the line terminates at the thread, a PEB branch tee does the same job. In either case the tube OD must match the fitting exactly.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED804
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.