Airtac PED T-Shaped Side Thread Tee Fitting PED804-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED804-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED804-S
The AirTAC PED804-S is a male run tee from the PED one-touch family: two Dia 8 mm legs accept soft nylon or polyurethane tube with a straight push, the internal chuck and stainless spring gasket grip it, and the release ring frees it again when you need to rework the line. The 1/2in PT male stud sits in the run, so a main supply can pass straight through the fitting while the perpendicular leg drops air off to a branch. That through-flow is what separates a run tee from a branch tee, where the line dead-ends.
This is the resin fitting spec profile, unchanged by the -S suffix: 0-1.0 MPa working pressure, 1.5 MPa proof pressure, -750 mmHg vacuum capability, and a -20 to +70 C temperature window. What -S buys you is a SUS304 stainless stud in place of the standard brass one, for corrosive or wash-prone mounting positions. The tee body itself stays PBT and every published dimension matches the standard PED804, so the two parts are mechanically interchangeable.
Airtac PED T-Shaped Side Thread Tee Fitting PED804-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED804-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED804-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED804-S Is Used
In-line drops on a bottling conveyor
Carry a 1/2in supply run along the conveyor frame and split a Dia 8 drop to each gripper or stopper cylinder, with the main line continuing to the next station.
Plating-line rinse bay plumbing
The SUS304 stud resists dulling and corrosion where the fitting sits in splash zones and frequent hose-down, positions that age a plain brass stud quickly.
Daisy-chained valve manifolds
Feed one manifold outlet from the 1/2in stud and let the run continue to a second manifold, so both banks share a single regulated supply leg.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED804-S the Right Part?
On the 1/2in thread, Dia 8 mm is the smallest tube PED offers, so there is no smaller tube size to step down to at this thread; the step down is PED803, the same Dia 8 run tee on a 3/8in stud, which suits mid-size valve and cylinder ports. Stepping up tube gives PED1004, Dia 10 on the same 1/2in thread, moving more air through the wider bore. Pick a run tee when the supply must continue past the branch point; if the line terminates at the fitting, a PEB branch tee is the leaner shape.
Match the 1/2in PT stud to the port before ordering: this catalogue documents PT threads only, and threaded parts arrive with sealant pre-applied. Tube OD must match exactly, because a Dia 8 chuck will not seal on 1/4in (6.35 mm) tube even though the sizes look close.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED804-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum capability -750 mmHg (10 Torr), operating temperature -20 to +70 C. The fitting joins Dia 8 mm soft nylon or polyurethane tube on two tee legs and presents a 1/2in PT male stud in the run. The body is PBT with a SUS304 stainless stud, POM release parts and an NBR O-ring; the -S suffix does not re-rate any of these figures.
No on both points. The SUS304 variant replaces the stud material only and shares the full PED804 dimension table, so drawings and panel cut-outs carry over. It still grips Dia 8 mm OD tube exclusively, and the thread is PT only; no NPT or G variant exists in this catalogue, and the stainless option is not offered on the metal BP family at all.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED804-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.