Airtac PH-1 Hex Head Toggle Joint PH1002
The AirTAC Airtac PH-1 Hex Head Toggle Joint PH1002 is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH1002
The PH1002 is an AirTAC PH universal male elbow, a one-touch fitting that joins Dia 10 mm soft nylon or polyurethane tube to a 1/4 in PT male thread. Push the tube into the POM chuck and the stainless spring gasket grips it instantly; press the release ring and the tube frees again. Unlike the fixed-angle PL male elbow, the universal joint swivels, so the tube exit can be re-aimed even after the thread is tightened.
This part uses the resin and brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg, proof pressure 1.5 MPa and a -20 to +70 C temperature window. The body is PBT over a brass stud, the thread arrives with sealant pre-applied, and grey is the standard colour.
Airtac PH-1 Hex Head Toggle Joint PH1002 Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH1002 |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH1002
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH1002 Is Used
Robot gripper lines
On a pick-and-place wrist, the Dia 10 line feeding a gripper or ejector needs a final direction change in very little space. The PH1002 swivels, so the tube leaves at the angle the wrist motion demands without re-clocking the thread.
Cylinder ports in tight guards
Inside a machine guard, a 1/4 in cylinder port may face a bracket, sensor or frame rail. Screw the elbow in, then turn the head until the 10 mm tube runs clear of the obstruction.
Panel drop legs
From a manifold inside a control cabinet, the run down to an actuator bends around ducting and cable looms. A swivel Dia 10 elbow turns the drop to follow the loom route without kinking the tube.
Is the Airtac PH-1 Hex Head Toggle Joint PH1002 the Right Part?
On the 1/4 in thread row of the PH ladder, Dia 10 is the largest tube the series supports; the step down is the PH802 on Dia 8, which frees space around the port but slightly raises restriction through the bore. If your run needs Dia 12, this 1/4 in elbow cannot take it - move up to PH1003, the same swivel elbow on a 3/8 in thread. Match the thread to the port first, then let the swivel set the exit angle afterwards. Above all, tube OD must match exactly: a Dia 10 fitting will not seal on 8 mm or 12 mm tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH1002 FAQ
Working pressure is 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa and operating temperature -20 to +70 C. The fitting joins Dia 10 mm soft nylon or polyurethane tube to a 1/4 in PT male thread, with grey as the standard body colour.
A PL elbow presents the tube exit at one fixed angle, so thread orientation dictates tube direction. The PH swivel joint rotates after the thread is tightened, letting you clear guards, brackets or neighbouring fittings on ports that serve several machine layouts.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH1002
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.