Airtac PH-1 Hex Head Toggle Joint PH1002D
The AirTAC Airtac PH-1 Hex Head Toggle Joint PH1002D is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH1002D
PH1002D is an AirTAC PH universal male elbow in the black-body option, joining Dia 10 mm soft nylon or polyurethane tubing to a 1/4in PT male thread. On the PH series the D suffix changes the body itself to black, not just the release button, so the fitting stays discreet on dark machine frames. The one-touch joint works by pushing the tube past the POM release ring into the chuck: the stainless spring gasket and NBR O-ring grip and seal it, and pressing the ring again frees the tube. The male thread arrives with sealant already applied.
This part belongs to the resin and brass spec profile: 0-1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. That makes it a resin-line fitting, not the 0.9 MPa / 150 C metal BPC line. The universal elbow shape lets the outlet be clocked to the direction the tubing actually needs to run, so the tube leaves the port square instead of twisted.
Airtac PH-1 Hex Head Toggle Joint PH1002D Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH1002D |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH1002D
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH1002D Is Used
Vacuum ejector feed lines
Feeding a vacuum ejector on a pick-and-place gantry: the PH series is rated down to -750 mmHg, and the swivelling elbow lets the suction line drop away without side load on the generator port.
Tight machine-frame plumbing
Routing a Dia 10 supply drop inside a compact frame where a straight connector would kink the tubing - the elbow turns the run 90 degrees right at the port instead of in the tube.
Black-anodised assembly presses
Cylinder-port plumbing on assembly presses with dark frames: the black body blends into the machine rather than standing out like a standard grey fitting on a visible line.
Is the Airtac PH-1 Hex Head Toggle Joint PH1002D the Right Part?
On the PH ladder, a 1/4in thread carries Dia 6, 8 and 10 only, so PH1002D is the top of this thread's tube range - anything larger moves to a 3/8in or 1/2in thread version such as PH1203 for Dia 12. Step down and PH802 serves Dia 8 lines where a lighter actuator or shorter stroke calls for less bore. Match the thread to the port size; the factory-applied sealant means no extra tape is normally required. Tube OD must match exactly: a Dia 10 chuck will not grip 3/8in tubing even though the numbers look close.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH1002D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. This SKU joins Dia 10 mm soft nylon or polyurethane tube to a 1/4in PT male thread and comes with a black body.
No. The one-touch chuck grips a single tube OD only, so PH1002D holds Dia 10 mm tube exactly. For Dia 12 on the PH series you need a 3/8in or 1/2in thread version such as PH1203 - a PH 1/4in thread never carries Dia 12.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH1002D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.