Airtac PH-1 Hex Head Toggle Joint PH1002D-S
SUS304 stainless variant (-S)The AirTAC Airtac PH-1 Hex Head Toggle Joint PH1002D-S is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH1002D-S
The PH1002D-S is an AirTAC PH universal female elbow: a one-touch fitting that connects Dia 10 mm soft nylon or polyurethane tube to a 1/4in PT female thread. Push the tube straight into the chuck and the stainless spring gasket grips it for a sealed joint; press the POM release ring and the tube slides straight back out. The female port means the stud thread arrives with sealant already applied, so it screws directly onto a male port without extra tape or compound.
This is the resin spec profile, not the metal BP line: 0-1.0 MPa working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70 C. The -S suffix on an elbow-family code like this one denotes a SUS304 stud rather than a solid stainless body; the black PBT body, POM release ring, aluminium guide and NBR O-ring are unchanged, and every pressure and temperature figure matches the standard PH1002D. AirTAC publishes no corrosion class or certification for the -S line, so buy it for stud corrosion resistance in damp or wash-down plant, not against a printed standard.
Airtac PH-1 Hex Head Toggle Joint PH1002D-S Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH1002D-S |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH1002D-S
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH1002D-S Is Used
Injection mould gate cylinder
A 10 mm bore line feeding a mould-open cylinder on an injection press, with the swivel elbow aimed around a tie-bar after the 1/4in port is made up.
Wash-down packaging conveyor
A packaging conveyor cell hosed down at shift end: the SUS304 stud holds up at the port where a plated brass stud would corrode first, with a 10 mm line to a divertor cylinder.
Vacuum pick head on a lab filler
A small-batch vial filler using -750 mmHg vacuum cups; the female elbow orients the drop toward the cup manifold, and the resin profile is fully rated for that vacuum.
Is the Airtac PH-1 Hex Head Toggle Joint PH1002D-S the Right Part?
On the PH ladder a 1/4in thread takes Dia 6, Dia 8 or Dia 10 tube only, so PH1002D-S sits at the top of that rung: the size down is the PH802 (Dia 8, a lighter line for smaller actuators), and there is no Dia 12 option on 1/4in. If the run needs 12 mm bore, step up to a 3/8in thread, which is the first rung on PH that accepts Dia 12. Tube OD must match exactly either way - a Dia 10 chuck will not seal on 1/4in (6.35 mm) tube, however close it looks.
Pick the PH shape over a plain PL male elbow when the port thread is female and the direction of the run is decided on the machine, not on the drawing: the universal joint lets you swing the tube exit to the best angle after the fitting is installed. Choose PLM or PMF instead if the run has to pass through a panel wall.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH1002D-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. The fitting connects Dia 10 mm soft nylon or polyurethane tube to a 1/4in PT female thread on a universal swivel elbow. The -S variant carries exactly these same figures as the standard PH1002D; the SUS304 stud changes materials at the port, not ratings.
No, and it is worth knowing before you specify it. On the elbow and tee families, the -S suffix means the threaded stud is SUS304 while the body stays PBT - black on this code, because the D suffix sets body colour on the PH series. Only the PC and POC straight connectors get a solid SUS304 body in the stainless range. If you need an all-stainless body on an elbow, this catalogue does not publish one; if you need corrosion resistance at the machine port itself, the SUS304 stud is the part that meets the thread and does that job.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH1002D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.