Airtac PH-1 Hex Head Toggle Joint PH1203-S
SUS304 stainless variant (-S)The AirTAC Airtac PH-1 Hex Head Toggle Joint PH1203-S is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH1203-S
The PH1203-S is an AirTAC PH universal male elbow with a SUS304 stainless stud. The thread side screws into a 3/8in PT port, and the swivel body can then be turned to the exact angle you need before the tube is inserted, so a Dia 12 line can leave the port at any orientation without kinking or side-loading the seal. One-touch connection: push soft nylon or polyurethane tubing fully home, the POM chuck grips it, and pressing the release ring frees it again.
This sits on the resin one-touch spec profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. The -S suffix on a PH part means the STUD is SUS304 while the body stays PBT, so you get a corrosion-resistant, non-rusting thread interface where the fitting meets the machine port, with the pressure, vacuum and temperature figures identical to the standard PH1203.
Airtac PH-1 Hex Head Toggle Joint PH1203-S Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH1203-S |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH1203-S
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH1203-S Is Used
Rotary actuator port
A swivel elbow on the 3/8in PT port of a rotary vane actuator lets the Dia 12 air line leave at whatever angle the swing clearance demands, instead of fighting a fixed elbow that twists the hose each rotation.
Plating line rinse station
On a copper-plating or electroplating rinse rig, the SUS304 stud at the port resists the damp, chemical-laden air that rusts plain brass threads, while the PBT body shrugs off splash.
Trailer-mounted air tool feed
On a lorry tail-lift or trailer air circuit, a Dia 12 swivel elbow at the manifold port lets the polyurethane line route downward into a sleeve, absorbing vibration without the fitting working loose.
Is the Airtac PH-1 Hex Head Toggle Joint PH1203-S the Right Part?
Dia 12 is the largest tube the PH 3/8in row supports. One step down is PH1003 (Dia 10 on 3/8in PT), which suits lighter actuator lines at the same port thread; for a bigger flow path on the same Dia 12 tube, step up to PH1204 on 1/2in PT. Note the PH ladder narrows on small threads: 1/8in PT on this prefix only takes Dia 4, 6 and 8, so a small-thread swivel with a 12mm bore does not exist. Tube OD must match exactly - a Dia 12 fitting will not hold 1/4in or 5/8in hose.
Choose this universal elbow over a fixed PL when the port position forces an awkward tube exit: thread in, rotate the body to clear guards or brackets, then lock the angle by seating the tube. The 3/8in PT thread arrives with sealant pre-applied, so no tape or paste is needed on the port.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH1203-S FAQ
Tube size Dia 12 mm, thread 3/8in PT, universal male elbow shape with a SUS304 stud. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Applicable tubing is soft nylon or polyurethane.
No. On the PH series, -S means the threaded stud is SUS304; the swivel body remains PBT with a POM chuck, aluminium-alloy guide and NBR O-ring. Pressure, vacuum, proof-pressure and temperature ratings are unchanged from the standard PH1203, and the dimensions match the standard part exactly.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH1203-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.