Airtac PH-1 Hex Head Toggle Joint PH602
The AirTAC Airtac PH-1 Hex Head Toggle Joint PH602 is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH602
PH602 is the AirTAC PH series universal male elbow in the Dia 6 mm by 1/4 in size. It screws into a female PT port and gives you a one-touch outlet for 6 mm soft nylon or polyurethane tube, with the swivel body free to sit at whatever angle the installation needs. That is the whole point of the PH shape: instead of bending the tube around to reach an awkwardly clocked port, you thread the fitting in and pivot the outlet to the run you want.
Push the tube home and the stainless spring gasket and chuck inside grip it for a pressure-tight joint; press the release ring and the tube slides straight out for rework or re-routing. This is the resin one-touch line, not the metal BP family: working pressure 0 to 1.0 MPa, proof pressure 1.5 MPa, temperature -20 to +70 C, vacuum to -750 mmHg (10 Torr). The threaded section is PBT with a brass stud and arrives with sealant already applied to the PT thread, so it goes straight onto the port as supplied.
Airtac PH-1 Hex Head Toggle Joint PH602 Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH602 |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH602
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH602 Is Used
Gripper ports on pick-and-place arms
Compact grippers often have their air port facing into the wrist mechanism, so a fixed elbow would force the 6 mm tube through a tight bend. The PH602 swivels to point the outlet along the arm's cable run instead, protecting the tube through every cycle of the stroke.
Sealing-jaw cylinders in packaging machines
Jaw cylinders on vertical form-fill-seal machines sit close behind guarding, leaving little room to route 6 mm tubing. Threading a PH602 into the cylinder port and pivoting the outlet away from the guard lets the tube leave square, with the pre-applied PT sealant sealing the port on assembly.
Rotary index-table actuators
On a rotary actuator the port clock angle changes as the actuator is set up, so a rigid elbow may end up facing the wrong way. With a PH602 the outlet can be re-angled at commissioning without buying a different fitting, and the one-touch release lets the 6 mm tube be lifted out if the direction is changed again.
Is the Airtac PH-1 Hex Head Toggle Joint PH602 the Right Part?
On a 1/4 in PT thread the PH ladder runs Dia 6, 8 and 10, so PH602 is the smallest tube size this thread supports - there is nothing below Dia 6 on a 1/4 in PH. Step up to PH802 for 8 mm tube or PH1002 for 10 mm; the only change is the bore the chuck takes. If your tube is 6 mm but the port is 1/8 in, PH601 covers that pair instead. Match the thread to the port first, then the tube: the one-touch chuck grips only the exact OD it is made for, so a Dia 6 fitting will not hold 1/4 in tube and vice versa. Where the outlet has to pass through a panel wall or branch off a straight run, a PMF bulkhead connector or a PEB branch tee is the better shape than a swivel elbow.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH602 FAQ
It is a Dia 6 mm one-touch outlet on a 1/4 in PT male thread, from the resin one-touch line. Working pressure is 0 to 1.0 MPa (0 to 10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and the temperature range is -20 to +70 C. Use soft nylon or polyurethane tubing only.
Yes. The universal joint between the male thread and the elbow body is what separates PH from the fixed PL elbow: the thread seats in the port, then the outlet can be set to the angle the tube run needs. Note that AirTAC publishes no tightening torque for these fittings - seat the sealed PT thread as you would any pre-sealed brass-stud fitting and set the angle by hand on the swivel.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH602
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.