Airtac PH-1 Hex Head Toggle Joint PH602-S
SUS304 stainless variant (-S)The AirTAC Airtac PH-1 Hex Head Toggle Joint PH602-S is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH602-S
The AirTAC PH602-S is a universal male elbow from the resin one-touch range: it joins Dia 6 mm soft nylon or polyurethane tubing to a 1/4 inch PT male thread. Where a fixed PL elbow locks the outlet at 90 degrees, the universal head swivels on its stud, so the outlet can be aimed at any angle the tube run needs - and re-aimed after the thread is tightened. Push the tube home and the internal chuck grips it; press the POM release ring to free it.
This -S variant keeps the PBT elbow body and replaces the standard brass stud with a SUS304 stainless steel one, which helps wherever moisture or rinse-down would pit a brass thread. Ratings are identical to the standard line: 0 to 1.0 MPa working, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure, -20 to +70 C. Be clear about the scope: on PH-series -S parts only the stud is stainless; the body itself is not.
Airtac PH-1 Hex Head Toggle Joint PH602-S Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH602-S |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH602-S
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH602-S Is Used
Aimed drops at cylinder ports
On a packaging machine gripper cylinder, the swivel head lets the Dia 6 outlet point along the inside of the guard even when the 1/4in port faces the wrong direction.
Washdown conveyor take-ups
The SUS304 stud stands up to repeat rinse-downs on food conveyor take-up frames where a bare brass thread would corrode, at the same 1.0 MPa rating.
Rotary index table rebuilds
Clocking the outlet after install suits index-dial manifolds, where the Dia 6 tube route to the rotary union changes each time the tooling is swapped.
Is the Airtac PH-1 Hex Head Toggle Joint PH602-S the Right Part?
On the 1/4 inch rung of the PH ladder the available tubes are Dia 6, 8 and 10, so PH602-S is the smallest tube that pairs with this port; step up to PH802 for Dia 8. If your port is 1/8 inch, the Dia 6 equivalent is PH601. Threaded studs in this family arrive with sealant pre-applied, while the M5 sizes in the range seal with a gasket instead. Tube OD must match exactly - a Dia 6 chuck will not hold 6.35 mm (1/4 inch) tube, and forcing it will leak.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH602-S FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. It connects Dia 6 mm soft nylon or polyurethane tube to a 1/4 inch PT male thread. The -S suffix means the stud is SUS304 stainless steel while the elbow body remains PBT.
No. AirTAC publishes identical pressure, vacuum, temperature and dimension figures for the standard and -S PH elbows; the change is the SUS304 stud replacing the brass one. This family is not a solid stainless body, and no passivation, surface finish or food certificate is published for it.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH602-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.