Airtac PH-1 Hex Head Toggle Joint PH602D
The AirTAC Airtac PH-1 Hex Head Toggle Joint PH602D is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH602D
The PH602D is an AirTAC PH universal male elbow, the swivelling cousin of the fixed PL elbow. Its male thread is 1/4in PT and its chuck accepts Dia 6 mm soft nylon or polyurethane tubing. Because the elbow head rotates through any angle after the thread is installed, you thread the body into the port first, then swing the tube outlet to exactly the direction your hose needs - no more lining up a fixed 90 degree part with the machine.
This is the resin one-touch profile, not the metal line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. The D suffix on a PH series part means the black body option, not just a black button - the whole fitting leaves the factory in black instead of the standard grey. The PT thread arrives with sealant already applied, and the internal POM chuck with stainless spring gasket grips the tube the moment it is pushed home.
Airtac PH-1 Hex Head Toggle Joint PH602D Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH602D |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH602D
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH602D Is Used
Cylinder ports on packaging machinery
Swing the outlet clear of a guarding plate on a horizontal form-fill-seal machine: thread the 1/4in PT stud into the cylinder, then rotate the Dia 6 outlet to face the airline run without repositioning the actuator.
SCARA robot gripper circuit
On a compact SCARA end-of-arm tooling head, a universal elbow lets the Dia 6 hose exit sideways or upward as the wrist rotates, avoiding the hose wrap a straight or fixed 90 degree connector forces.
Jig and fixture rebuild benches
When reworking pneumatic clamps on welding jigs, one PH602D replaces several fixed-angle elbows: set the thread once, then re-aim the Dia 6 drop to the new clamp position without buying a different part.
Is the Airtac PH-1 Hex Head Toggle Joint PH602D the Right Part?
On the 1/4in PH ladder the sizes are Dia 6, Dia 8 and Dia 10 - there is no PH in 1/4in below Dia 6, so this is the smallest tube this thread takes; step up to PH802 for Dia 8 tube. If your port is only 1/8in, PH601 covers Dia 6 on that thread instead, and PH603 moves the same Dia 6 tube up to a 3/8in port. Keep one rule absolute: tube OD must match the code exactly, so a Dia 6 PH602D will not seal on 1/4in (6.35 mm) imperial hose.
Choose PH over PL when the outlet direction is unknown at design time or changes between machine variants - the fixed PL saves money but locks you to one angle. Choose PMF or PLM instead when the tube has to pass through a panel wall.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH602D FAQ
It is a Dia 6 mm universal male elbow with a 1/4in PT thread, rated 0-1.0 MPa working pressure (0-10 kgf/cm2), -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure, and -20 to +70 C operating temperature. Tubing must be soft nylon or polyurethane of exactly Dia 6 mm OD. The PT thread ships with sealant applied.
A PL elbow is fixed at 90 degrees: the tube outlet points one way only, and the thread has to be tightened to that exact clocking. The PH head swivels, so after threading the stud into the port you can set the Dia 6 outlet to any angle and the seal is made by the thread sealant, not by the elbow position. Use PH wherever port clocking is awkward or the hose route may change.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH602D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.