Airtac PH-1 Hex Head Toggle Joint PH802
The AirTAC Airtac PH-1 Hex Head Toggle Joint PH802 is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH802
The PH802 is an AirTAC PH universal male elbow, a resin one-touch fitting that takes Dia 8 mm soft nylon or polyurethane tube into a 1/4" PT male thread. Unlike a fixed PL elbow, the universal head swivels on the thread seat, so after you have screwed the 1/4" stud into the port you can rotate the elbow body to point the tube exit exactly where the run needs it. Push the tube home and the internal chuck grips it; press the POM release ring to let it go.
This is the resin/brass spec profile, not the metal BPC line: 0-1.0 MPa working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70 C. The body is PBT with a brass stud, a POM release button and chuck, an aluminium-alloy guide, a stainless spring gasket and an NBR O-ring. AirTAC ships the thread pre-coated with sealant, so no extra tape or paste is needed on the 1/4" PT side.
Airtac PH-1 Hex Head Toggle Joint PH802 Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH802 |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH802
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH802 Is Used
Cylinder ports behind tight guarding
On a packaging machine where the guard panel sits close to the cylinder's rear port, the PH802's swivelling elbow turns the line 90 degrees and lets you aim the Dia 8 tube away from the sheet metal after the 1/4" stud is torqued in.
Pilot air feeds on solenoid valve manifolds
Feeding pilot or signal air to a 5/2 valve bank from Dia 8 polyurethane tube: the 1/4" PT stud seats on the valve port with the factory-applied sealant, and the universal head lines up with the valve's tube slot even when port faces vary.
Vacuum ejector drop on pick-and-place heads
A compact suction-cup ejector on a robotic gripper often needs its supply line entering sideways. This elbow's -750 mmHg vacuum rating covers the ejector supply, and the swivel keeps the Dia 8 tube clear of the robot's dress pack.
Is the Airtac PH-1 Hex Head Toggle Joint PH802 the Right Part?
On the PH ladder at 1/4" you have Dia 6 below and Dia 10 above this Dia 8 fitting. Stepping to Dia 6 gives you a leaner bore for small cylinders and pilot lines; stepping to Dia 10 lowers restriction for longer runs or larger bores. Thread-wise, Dia 8 is also made in 1/8" and 3/8" on the PH, but note the PH ladder caps 1/8" at Dia 8 - larger tube on PH needs 3/8" or 1/2" thread. Tube OD must match exactly: a Dia 8 chuck will not seal on 1/4" (6.35 mm) or 5/16" tube.
Choose this PH shape over a PL elbow when the port orientation is fixed but your tube route is not - the swivel head absorbs misalignment. If the fitting has to pass through a panel wall instead, that is a PMF bulkhead job, not this one.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH802 FAQ
The PH802 is a Dia 8 mm one-touch universal male elbow with a 1/4" PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and the temperature range is -20 to +70 C. It suits soft nylon or polyurethane tube only, in grey as standard.
No tape is needed - AirTAC applies thread sealant to the 1/4" PT stud before shipping, so it seals straight into the port. Yes to the second part: the universal head swivels relative to the stud, so once the thread is tight you can still rotate the body to point the Dia 8 tube exit in the direction your hose run needs.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH802
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.