The AirTAC Airtac PHW F Thread Swivel Tee Fitting PHW1002 is a genuine double universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
The AirTAC PHW1002 is a double universal male elbow: a one-touch fitting that takes Dia 10 mm soft nylon or polyurethane tube into a 1/4 in PT male thread, with two swivel joints so the outlet can be set at any angle after the thread is installed. Push the tube home and the internal chuck grips it under spring load; press the POM release ring and the tube frees again for rework.
This is the resin-brass one-touch profile: working pressure 0-1.0 MPa, vacuum down to -750 mmHg, proof pressure 1.5 MPa, and a service window of -20 to +70 C. The elbow body is moulded PBT on a brass stud, the shank arrives with sealant already on the thread, and the release button, chuck and stainless spring gasket are shared across the whole PHW family.
| Model | Airtac PHW F Thread Swivel Tee Fitting PHW1002 |
|---|---|
| Type | Double universal male elbow |
| Series | PHW |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
| PHW | Double universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Threaded into a 1/4 in valve manifold port, the double swivel lets the Dia 10 tube leave at whatever angle the ducting demands instead of forcing the valve body to be rotated.
On a carton-eject gate, the pusher cylinder port often points sideways; PHW1002 takes the 1/4 in thread and swings the 10 mm supply line clear of the guard rail.
In a machining fixture with clustered clamps, the double universal joint routes the 10 mm air line around locating pins and chip guards without bending stress at the tube entry.
PHW on a 1/4 in thread accepts Dia 6, Dia 8 or Dia 10 tube, so PHW1002 sits at the top of this thread's ladder. The step down is PHW802 (Dia 8), which buys a slimmer profile on the same port; there is no Dia 12 option at 1/4 in on PHW. If you need Dia 12, step the port up to 3/8 in and use PHW1203. Match the 1/4 in thread to the port you actually have - a 1/8 in port will not seal a 1/4 in stud regardless of thread tape. Tube OD must match exactly: a Dia 10 fitting will not hold 3/8 in tube and vice versa. If the run only needs a fixed right angle, a plain PL male elbow is cheaper; choose PHW when the thread cannot be clocked or the tube must leave at a non-90 degree angle.
Quick checklist
PHW1002 is a double universal male elbow for Dia 10 mm tube with a 1/4 in PT male thread. It is part of the resin one-touch line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum capability -750 mmHg, proof pressure 1.5 MPa, and an operating temperature range of -20 to +70 C. It is rated for soft nylon or polyurethane tubing only, and the PT shank arrives with sealant pre-applied.
Both joints rotate so you can set the tube outlet angle after tightening, which is the point of the double universal design over a fixed PL elbow. The seal is made at the male thread itself; once the stud is seated in the port with its pre-applied sealant, the swivel action happens downstream of the thread, so re-angling the body does not loosen the joint or leak.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard parts are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.