Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S
SUS304 stainless variant (-S)The AirTAC Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S is a genuine double universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeDouble universal male elbow
- SeriesPHW
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S
The PHW1002D-S is an AirTAC double universal male elbow: a one-touch fitting that joins Dia 10 mm soft nylon or polyurethane tubing to a 1/4 in PT male port, with a swivel joint at BOTH ends rather than just the thread. Push the tube past the guide into the chuck and the stainless spring gasket grips it against internal pressure; press the POM release ring and the tube frees for repositioning. Because both the thread end and the tube end pivot, you can route the incoming line at any angle without fighting the fitting into alignment. The trailing -S means the male stud is SUS304 stainless steel; on the PHW shape the main body stays glass-reinforced PBT, so this is a corrosion-resistant connection point rather than an all-stainless part. The D suffix gives the body in black instead of the standard grey.
This belongs to the resin/brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg, proof pressure 1.5 MPa, and a service temperature of -20 to +70 C. The 1/4 in PT thread arrives from AirTAC with sealant already applied to the male thread, so it seals on tape-free assembly; the release button, chuck and O-ring keep their standard POM and NBR construction on the -S version.
Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S Technical Specifications
| Model | Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S |
|---|---|
| Type | Double universal male elbow |
| Series | PHW |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S
| PHW | Double universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S Is Used
Pick-and-place end-of-arm tooling
On a robotic gripper arm, the vacuum or actuation line enters at an angle that changes with the wrist pose. The PHW1002D-S swivels at both the 1/4 in PT port and the 10 mm tube end, so the hose tracks the motion instead of loading the fitting sideways.
Indexing dial machine plumbing
Rotary indexing tables carry cylinder ports that point wherever the turret stops. A double universal elbow at each Dia 10 station lets the fixed manifold plumbing stay straight while the fitting self-aligns to the rotating port.
Adjustable conveyor guide-rail actuators
Guide-rail width cylinders get repositioned and re-plumbed during changeover. The black PBT body resists knock-on damage in the frame, and the 10 mm bore feeds compact air cylinders without throttling their cycle speed.
Is the Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S the Right Part?
Within the 1/4 in PT row of the PHW ladder, the sizes available are Dia 6, 8 and 10, so this Dia 10 version is the LARGEST tube the 1/4 in thread takes. Stepping down to PHW0802 gives you a lighter 8 mm line and slightly better access in tight tooling; there is no larger tube on 1/4 in. If the circuit later grows to 12 mm, you must move the thread up as well, because 1/2 in on PHW starts at Dia 8 and PHW1204 is the natural next step. Whichever way you go, the tube OD must match the fitting exactly: a Dia 10 chuck will not seal on 3/8 in or 5/16 in tube, and forcing a near-size in is the most common cause of a slow leak on one-touch joints.
Choose the double-swivel PHW shape over the single-swivel PH or PHF when the port orientation AND the incoming hose direction are both outside your control, which is typical on rotating or adjustable subassemblies. If you actually need to join two tube runs with no thread at all, that is the PV union elbow instead, a different series entirely.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2); vacuum capability -750 mmHg (10 Torr); proof pressure 1.5 MPa; operating temperature -20 to +70 C. Tube size Dia 10 mm (soft nylon or polyurethane), thread 1/4 in PT male. Construction: PBT body in black (D suffix), SUS304 stainless male stud, POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring. Flow is published by AirTAC as a characteristic curve only, tied to the 10 mm bore.
No. On the PHW family, the -S option puts the SUS304 male stud on the threaded end; the elbow body remains PBT, which is why the published pressure, vacuum and temperature figures are identical to the standard PHW1002D. AirTAC publishes no corrosion class, surface finish or certification for the -S line, so it should be specified for corrosion-prone or copper-sensitive mounting points based on the stud material alone, not on a certification claim.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PHW F Thread Swivel Tee Fitting PHW1002D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.