Airtac PHW F Thread Swivel Tee Fitting PHW802
The AirTAC Airtac PHW F Thread Swivel Tee Fitting PHW802 is a genuine double universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeDouble universal male elbow
- SeriesPHW
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PHW F Thread Swivel Tee Fitting PHW802
The PHW802 is an AirTAC double universal male elbow: a one-touch fitting that joins Dia 8 mm soft nylon or polyurethane tube to a 1/4" PT male port, with a swivel joint at both ends of the elbow. Push the tube into the chuck and the stainless spring gasket grips it for a pressure-tight seal; press the POM release ring and the tube frees off again. The male thread arrives pre-coated with sealant, so no extra tape or paste is needed on the port.
This is the resin one-touch family, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum down to -750 mmHg (10 Torr), and a service temperature of -20 to +70 C. The body is PBT with a brass stud, POM release button, aluminium-alloy guide and an NBR O-ring. Grey is standard; a D suffix version changes the release button to black.
Airtac PHW F Thread Swivel Tee Fitting PHW802 Technical Specifications
| Model | Airtac PHW F Thread Swivel Tee Fitting PHW802 |
|---|---|
| Type | Double universal male elbow |
| Series | PHW |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PHW F Thread Swivel Tee Fitting PHW802
| PHW | Double universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PHW F Thread Swivel Tee Fitting PHW802 Is Used
Robot end-of-arm air feed
On a pick-and-place robot wrist, a Dia 8 line feeding a gripper often needs the elbow pointed in an awkward plane. The double universal joint on PHW802 lets the fitter aim the tube run after mounting, without adding a second swivel.
Indexing dial machine ports
Rotary indexing tables present their 1/4" ports at odd angles as the dial turns through stations. PHW802 takes the Dia 8 tubing and lets each station's drop be set true, avoiding side load on the tube at the chuck.
Packaging machine head routing
Carton-sealing and wrapping heads pack cylinders and sensors into tight frames. The 8 mm bore suits the short, high-delivery drops typical of these heads, and the swivelling elbow clears guard plates where a rigid PL cannot.
Is the Airtac PHW F Thread Swivel Tee Fitting PHW802 the Right Part?
Size both ways before ordering. Step the tube down and the equivalent fitting is PHW602 (Dia 6 tube, 1/4" thread) feeding lighter lines; step up to PHW1002 (Dia 10 tube, 1/4" thread) for higher-delivery branches. Holding the 8 mm tube and changing the port instead gives PHW801 on 1/8" or PHW803 on 3/8". Note that the PHW ladder on a 1/4" thread runs only Dia 6, 8 and 10 - there is no Dia 4 or Dia 12 double universal elbow on this thread, and the series starts at 1/8" with no M5 version at all.
Choose PHW over a fixed PL elbow when the elbow must be aimed after the port is made: both swivel ends let you set the run angle in any plane, which saves a second fitting. The tube must be exactly Dia 8 - a 5/16" or 1/4" tube will not seat in the chuck.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PHW F Thread Swivel Tee Fitting PHW802 FAQ
PHW802 is a double universal male elbow for Dia 8 mm tube on a 1/4" PT male thread. Working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, negative pressure to -750 mmHg (10 Torr), operating temperature -20 to +70 C. It takes soft nylon or polyurethane tube. Body is PBT with a brass stud; release button and chuck are POM, guide is aluminium alloy, spring gasket stainless, O-ring NBR.
Yes. Both ends of the elbow pivot, so the tube direction can be set once the 1/4" thread is tightened into the port - that is the point of the double universal design over a fixed PL elbow. Thread the male end in with the factory-applied sealant (no extra tape needed), then orient the swivel to suit the run. AirTAC publishes this series in PT thread only; there is no G or NPT code to order instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PHW F Thread Swivel Tee Fitting PHW802
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.