Airtac PHW F Thread Swivel Tee Fitting PHW802D
The AirTAC Airtac PHW F Thread Swivel Tee Fitting PHW802D is a genuine double universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeDouble universal male elbow
- SeriesPHW
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PHW F Thread Swivel Tee Fitting PHW802D
The PHW802D is an AirTAC PHW double universal male elbow: a one-touch push-in fitting with a 1/4" PT male thread at the base and two swivel joints, so the Dia 8 mm tube can enter from almost any angle while the thread stays aligned with its port. Push the tube home and the internal chuck grips it; press the release ring to free it. Unlike the single-universal PH, the double joint lets the tubing leg swing through a wider arc, which is what makes the shape useful around rotating or adjustable sub-assemblies.
This is the resin and brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa, vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. The body is PBT, the D suffix makes it black rather than the standard grey, and the PT thread arrives pre-coated with sealant so it seals on the port without extra tape.
Airtac PHW F Thread Swivel Tee Fitting PHW802D Technical Specifications
| Model | Airtac PHW F Thread Swivel Tee Fitting PHW802D |
|---|---|
| Type | Double universal male elbow |
| Series | PHW |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PHW F Thread Swivel Tee Fitting PHW802D
| PHW | Double universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PHW F Thread Swivel Tee Fitting PHW802D Is Used
Robot wrist air feed
On a six-axis pick-and-place arm, the gripper air line has to follow a joint that rotates through nearly a full turn. The PHW802D double swivel lets the Dia 8 tube enter from the angle the dress-pack dictates while the 1/4" thread lands squarely on the wrist manifold port.
Packaging machine adjustable guide
Width-adjustable guides on a carton wrapper move every changeover, and hard-fixed elbows tear their tube legs when repositioned. A double universal elbow keeps the Dia 8 polyurethane line free to re-angle with the guide, threaded 1/4" into the clamp cylinder.
Press tooling rework
When a die set is rebuilt, the port orientation rarely ends up where the original drawing put it. The two swivel joints of the PHW802D absorb that mismatch, letting a Dia 8 nylon line route cleanly back to the manifold without kinking at the threaded port.
Is the Airtac PHW F Thread Swivel Tee Fitting PHW802D the Right Part?
On the PHW ladder at 1/4" thread, the neighbouring tube sizes are Dia 6 (PHW602) and Dia 10 (PHW1002). Stepping down to Dia 6 suits lighter lines to small actuators and signal-air circuits; stepping up to Dia 10 gives a noticeably larger bore for short, high-consumption cylinder feeds. Note that PHW is one of the few threaded prefixes with no M5 option at all - the smallest thread available is 1/8", so M5 ports must use the PH or PHF instead. The 1/4" PHW thread accepts Dia 6, 8 or 10, and PHW802D sits in the middle of that trio.
Match the thread to the port, not to habit: 1/4" PT is the common cylinder and valve port size on mid-size machinery. The tube must be exactly Dia 8 soft nylon or polyurethane - a 5/16" (8 mm nominal is fine, but 1/4" tubing is Dia 6.35 mm equivalent territory) mismatch or an imperial-size tube will not seal in the chuck. If you only need one swivel and a fixed angle, the PH single universal elbow is the simpler part; choose PHW when the tubing route must clear an obstruction from a direction the port cannot face.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PHW F Thread Swivel Tee Fitting PHW802D FAQ
It is a Dia 8 mm tube, 1/4" PT male thread double universal male elbow from AirTAC's resin one-touch range. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Tubing is soft nylon or polyurethane, and the D suffix gives a black body instead of grey.
PH gives you one swivel joint, so the tube enters at one adjustable angle. PHW adds a second joint, so the tubing leg can swing through a much wider arc - the right answer when the line has to reach around a guard, a rotating axis, or a port that faces the wrong way. Also note PHW is made without any M5 thread size; M5 ports need the PH or PHF series. And whatever the shape, the tube must be exactly Dia 8 - a Dia 6 fitting will not hold Dia 8 tube.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PHW F Thread Swivel Tee Fitting PHW802D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.