Airtac PHW F Thread Swivel Tee Fitting PHW803D
The AirTAC Airtac PHW F Thread Swivel Tee Fitting PHW803D is a genuine double universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeDouble universal male elbow
- SeriesPHW
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PHW F Thread Swivel Tee Fitting PHW803D
PHW is AirTAC's double universal male elbow in the resin one-touch range: a male elbow that pivots at both the thread and the tube outlet, so a Dia 8mm line can be aimed at any angle off a 3/8in PT port. Push the soft nylon or polyurethane tube into the chuck until it bottoms; the stainless spring gasket and POM chuck grip it, and the release ring frees it again whenever the line needs rework.
This is the standard resin profile, not the metal BP line: 0 to 1.0 MPa working (vacuum to -750 mmHg), 1.5 MPa proof, and -20 to +70 C. The D suffix gives a black PBT body instead of grey on this series, and the brass stud arrives with sealant already applied. One detail worth knowing before you standardise on it: the PHW ladder starts at 1/8in thread, so unlike most of the range there is no M5 version of this shape.
Airtac PHW F Thread Swivel Tee Fitting PHW803D Technical Specifications
| Model | Airtac PHW F Thread Swivel Tee Fitting PHW803D |
|---|---|
| Type | Double universal male elbow |
| Series | PHW |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PHW F Thread Swivel Tee Fitting PHW803D
| PHW | Double universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PHW F Thread Swivel Tee Fitting PHW803D Is Used
Robot wrist gripper feed
A Dia 8 line to a wrist-mounted gripper passes through angles that change every cycle; the two independent swivels let the fitting follow the wrist instead of fighting it.
Control valve port clearance
A 3/8in PT port on a directional control valve takes the black elbow, aimed clear of adjacent solenoid coils in a crowded manifold stack.
Welding fixture clamp circuit
Dia 8 clamp cylinders set at odd pitches on a welding jig get their air at whatever angle the mounting face dictates, without twisting the tubing.
Is the Airtac PHW F Thread Swivel Tee Fitting PHW803D the Right Part?
On the 3/8in thread the PHW ladder runs Dia 6, 8, 10 and 12, so the steps either side of this part are PHW603 (Dia 6, a lighter line feeding small actuators) and PHW1003 (Dia 10, more bore for longer runs). Holding Dia 8 tube against a smaller port, PHW802 on 1/4in exists; for a 1/2in port use PHW804. Tube OD must match exactly - this chuck is cut for 8mm and will not seal 5/16in or 1/4in hose.
A double universal elbow earns its place where a fixed PL elbow would leave the tube kinked or side-loaded: set the thread angle first, then swing the tube head independently before pushing the tube home.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PHW F Thread Swivel Tee Fitting PHW803D FAQ
It is a resin one-touch fitting: 0 to 1.0 MPa (0 to 10 kgf/cm2) working pressure, proof pressure 1.5 MPa, vacuum to -750 mmHg (10 Torr), and a working temperature of -20 to +70 C. It joins Dia 8mm soft nylon or polyurethane tube to a 3/8in PT male thread, and the stud is supplied pre-coated with sealant.
Not in this catalogue. The PHW range is documented with PT thread only; no G (BSPP) or NPT ordering code exists for it. Handling a parallel port is a machine-side decision - a sealing washer or an adapter - rather than a different AirTAC part number.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PHW F Thread Swivel Tee Fitting PHW803D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.