Airtac PL L Connector PL602D
The AirTAC Airtac PL L Connector PL602D is a genuine male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale elbow
- SeriesPL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PL L Connector PL602D
The PL602D is an AirTAC PL male elbow, the 90-degree one-touch fitting that connects Dia 6 mm soft nylon or polyurethane tube to a 1/4" PT male thread. Push the tube into the chuck and it grips for pressure-tight service; press the release ring and the tube slides straight back out, so circuits can be reworked without cutting tube.
It belongs to the resin and brass profile: 0 to 1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. The POM release button and chuck sit on an aluminium-alloy guide over a stainless spring gasket and NBR O-ring. The body is PBT with a brass stud, and because this is a D-suffix part the elbow body itself arrives in black rather than the standard grey. AirTAC pre-applies thread sealant to the male stud, so it seals on the PT port straight out of the bag.
Airtac PL L Connector PL602D Technical Specifications
| Model | Airtac PL L Connector PL602D |
|---|---|
| Type | Male elbow |
| Series | PL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PL L Connector PL602D
| PL | Male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PL L Connector PL602D Is Used
Cylinder ports inside machine guards
On a horizontal clamping cylinder mounted close to a frame rail, the elbow lets 6 mm PU tube exit vertically instead of fouling the guard panel, and the black body blends with black anodised hardware.
Adhesive dispense heads on packaging lines
A glue or sealant head fed from a 1/4" PT drop line takes its 6 mm supply at a right angle, keeping hose runs short and away from the hot nozzle zone.
Pneumatic training and demo rigs
Panel-mounted 1/4" PT ports on a teaching bench accept the male stud directly, while the black elbows make tube routing legible against grey manifolds for students tracing circuits.
Is the Airtac PL L Connector PL602D the Right Part?
On the 1/4" thread ladder of the PL series, Dia 6 sits between PL402 (Dia 4) below and PL802 (Dia 8) above. Stepping down to 4 mm trims the bore for light-duty pick-and-place lines; stepping up to 8 mm raises the cross-section feeding the actuator. If your port is a 1/8" thread, the same 6 mm tube is served by PL601 instead. Note that a one-touch chuck holds only its exact tube size: this fitting will not retain 1/4" OD tube, which measures about 6.35 mm.
Choose the PL elbow over a straight PC connector wherever the tube must leave a port at a right angle and a tight bend radius would kink soft polyurethane. If you need to pass through a panel wall instead, that is the job of the PLM bulkhead male elbow; the PLL extended male elbow is the pick when clearance for a spanner is tight at the port.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PL L Connector PL602D FAQ
Working pressure 0 to 1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum capability -750 mmHg (10 Torr), operating temperature -20 to +70 C. The fitting accepts Dia 6 mm soft nylon or polyurethane tube and carries a 1/4" PT male thread with factory-applied sealant. Stainless spring gasket and NBR O-ring inside; PBT body with brass stud, in black because of the D suffix.
No. 1/4" nominal tube has an OD of about 6.35 mm, which the Dia 6 chuck will not grip reliably; the tube OD must match exactly. Use genuine 6 mm OD tubing here, or move to PL402 for 4 mm tube, PL802 for 8 mm, PL102 for 10 mm or PL122 for 12 mm, all on the same 1/4" thread. For a 1/4 inch hose product you would need a different barb-style fitting entirely.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PL L Connector PL602D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.