Airtac PLF L-Shaped Female Thread Adapter PLF802
The AirTAC Airtac PLF L-Shaped Female Thread Adapter PLF802 is a genuine female elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeFemale elbow
- SeriesPLF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLF L-Shaped Female Thread Adapter PLF802
PLF802 is an AirTAC PLF series female elbow one-touch fitting: a Dia 8 mm tube socket set at 90 degrees to a 1/4 inch PT internal thread. Because the port is female, the fitting screws straight onto a male stud on a cylinder head, valve or manifold, and the tube enters from whichever side clears the surrounding machine frame. The body is PBT with a POM release button, stainless spring gasket and NBR seal; grey is standard, and a D suffix orders the black version.
Connection is one-touch: push soft nylon or polyurethane tube fully home and the internal chuck grips it; press the release ring to free it. This resin/brass profile is rated 0-1.0 MPa working pressure (0-10 kgf/cm2), -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. Every thread in this AirTAC catalogue is PT, and M5 sizes use a sealing gasket rather than sealant.
Airtac PLF L-Shaped Female Thread Adapter PLF802 Technical Specifications
| Model | Airtac PLF L-Shaped Female Thread Adapter PLF802 |
|---|---|
| Type | Female elbow |
| Series | PLF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLF L-Shaped Female Thread Adapter PLF802
| PLF | Female elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLF L-Shaped Female Thread Adapter PLF802 Is Used
Pallet clamp fixture cylinder
Screwed onto the male stud of a clamp cylinder on a die-change pallet, the 90 degree body routes a Dia 8 feed line down along the fixture plate where a straight connector would foul the clamp arm.
Vacuum ejector on robot gripper tooling
The -750 mmHg negative pressure rating lets the fitting carry the vacuum side of an ejector on pick-and-place end-of-arm tooling, with the elbow clearing the ejector body at the gripper frame.
FRL outlet drop at a compressor manifold
The 1/4 inch female port threads onto a lubricator or filter-regulator outlet stub in the compressor room, turning the Dia 8 line 90 degrees back toward the machine wall it feeds.
Is the Airtac PLF L-Shaped Female Thread Adapter PLF802 the Right Part?
On the tube side, PLF602 (Dia 6) and PLF1002 (Dia 10) bracket this SKU: stepping down trims the bore for light actuator circuits, stepping up suits longer runs and larger bore cylinders. On the thread side, PLF801 gives a 1/8 inch port and PLF803 a 3/8 inch port with the same Dia 8 tube socket. Order PL802 instead if your port takes a male stud rather than a female thread, or a PMF bulkhead if the line must pass through a panel wall.
Tube OD must match exactly: the Dia 8 socket will not grip or seal 1/4 inch (6.35 mm) tubing, and stiff non-nylon hose is outside the applicable-tube list.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLF L-Shaped Female Thread Adapter PLF802 FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg, proof pressure 1.5 MPa, operating temperature -20 to +70 C. Size: Dia 8 mm tube socket x 1/4 inch PT female thread. Grey PBT body with POM release button, stainless spring gasket and NBR seal; a D suffix orders the black version.
The socket accepts only Dia 8 mm soft nylon or polyurethane tube; 1/4 inch (6.35 mm) tube will neither grip nor seal. On the thread side, the female PT port mates with a male stud, so apply PTFE tape or sealant to that male thread. Note that this AirTAC one-touch catalogue documents PT threads only - no G or NPT variants exist.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLF L-Shaped Female Thread Adapter PLF802
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.