Airtac PLL L-Type Extended Thread Connector PLL1001D
The AirTAC Airtac PLL L-Type Extended Thread Connector PLL1001D is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL1001D
The PLL1001D is an AirTAC PLL extended male elbow, a one-touch fitting that joins Dia 10 mm soft nylon or polyurethane tube to a 1/8in PT male thread at a right angle. The extended male thread gives more standoff and engagement than the standard PL elbow, so the tube clears the mounting face instead of kinking against it. The D suffix makes the body black, and on the PLL series that colour change applies to the body itself, not just the release button.
Installation is push-in: square-cut the tube, push it fully home and the stainless spring gasket and chuck grip it against the POM seal for a leak-tight joint; press the release ring to free it. This is the resin/brass spec profile: 0 to 1.0 MPa working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70 C. The male thread arrives with sealant applied, so no extra tape or paste is needed.
Airtac PLL L-Type Extended Thread Connector PLL1001D Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL1001D |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL1001D
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL1001D Is Used
Pick-and-place gripper lines
On a pneumatic gripper arm, the 90 degree body with an extended stud keeps Dia 10 supply tube clear of the wrist casting, avoiding a crushed radius at the joint each time the wrist rotates.
Valve manifold outlet routing
Screw the 1/8in PT male thread straight into a solenoid valve outlet on a bottling or packaging machine manifold, and turn the air 90 degrees into the drop line to the actuator without an extra union.
Tight machine guarding retrofits
Behind sheet-metal guards where a straight connector cannot be reached, the extended elbow positions the Dia 10 tube where the release ring is still accessible for service.
Is the Airtac PLL L-Type Extended Thread Connector PLL1001D the Right Part?
This is the largest tube bore AirTAC offers on a PLL with a 1/8in thread - the ladder for this series stops at Dia 10 on 1/8in, so there is no PLL1201 above it. Stepping down to a PLL801 gets you a Dia 8 fitting with the same thread and a slightly smaller envelope; if your line is Dia 12 tube, move up to a PLL1202 on a 1/4in port instead. Thread choice follows the port, not the tube: match the 1/8in PT stud to a 1/8in tapped port and seal on the pre-applied thread coating.
Choose the extended shape over the standard PL elbow when the fitting sits behind a guard, a manifold face or a bracket, and the tube needs to stand off the wall to make its bend. Whichever size you pick, tube OD must match exactly - a Dia 10 chuck will not seal on 3/8in (10 mm nominal is close but not interchangeable with inch tube).
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL1001D FAQ
It is a PLL extended male elbow one-touch fitting with Dia 10 mm tube connection and a 1/8in PT male thread, black body. Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. It is rated for soft nylon or polyurethane tube, and the male thread ships with sealant applied.
No. The chuck and seal set is sized for Dia 10 mm tube only, and an undersized or oversized tube will not seal. Also note that on the PLL series 1/8in is the last thread size that takes Dia 10, so PLL1001D is the top of this bore; for Dia 12 tube you need a PLL1202 with a 1/4in male thread on the matching port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL1001D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.