Airtac PLL L-Type Extended Thread Connector PLL601
The AirTAC Airtac PLL L-Type Extended Thread Connector PLL601 is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL601
The PLL601 is an AirTAC PLL extended male elbow from the resin one-touch family: it connects Dia 6 mm soft nylon or polyurethane tubing to a 1/8in PT male parallel port, and the extended thread stud gives more clearance behind the hex than the standard PL elbow. Push the tube into the chuck until it bottoms out and the stainless spring gasket grips it; press the POM release ring to free it again.
This is the resin and brass spec profile, not the metal BPC line: working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure to -750 mmHg, proof pressure 1.5 MPa, temperature -20 to +70 C. The body is PBT with a brass stud, the release button and chuck are POM, the guide is aluminium alloy, and the O-ring is NBR. The 1/8in thread arrives pre-coated with sealant, so no extra PTFE tape is needed at assembly.
Airtac PLL L-Type Extended Thread Connector PLL601 Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL601 |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL601
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL601 Is Used
Cylinder ports behind machine guards
On a pick-and-place slide the cylinder port often sits in a recessed pocket. The extended 1/8in stud clears the guard boss so the hex can be reached with a spanner, and the 90-degree body turns the 6 mm drop line away from the moving carriage.
Packaging machine corner routing
On cartoning and wrap machines, tube runs follow the inside of the frame. A Dia 6 extended elbow at each direction change keeps the line flat against the frame rail instead of bowing outward, protecting the tube from abrasion on welded edges.
Pilot supply to 5/2 valve manifolds
A 1/8in PT tapped pilot port on a solenoid valve manifold takes the PLL601 directly. The pre-applied thread sealant means the elbow goes on without tape, and the Dia 6 outlet carries the pilot feed to a remote actuator.
Is the Airtac PLL L-Type Extended Thread Connector PLL601 the Right Part?
PLL601 sits mid-ladder. Stepping down to Dia 4 tube (PLL401) suits thin 4 mm drops to small grippers and pilot valves; stepping up to Dia 8 (PLL801) reduces flow resistance on longer cylinder feed lines. On the thread side you can go down to M5 (PLL6M5, sealed by a gasket rather than sealant) or up to 1/4in (PLL602) for larger valve ports. A 1/2in PLL exists only in Dia 10 and Dia 12, so it is not an option at Dia 6.
Match the thread to the port exactly: this is a PT male stud and must land in a tapped female port, not another fitting. Tubing OD must also match exactly - a Dia 6 chuck will not seal 1/4in tube. If you need to pass through a panel wall instead of turning a corner off a port, the PMF bulkhead connector or PLM bulkhead elbow is the correct shape.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL601 FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature range -20 to +70 C. It connects Dia 6 mm soft nylon or polyurethane tube to a 1/8in PT male thread, and the 1/8in stud arrives with sealant already applied.
No tape is needed: threaded AirTAC one-touch parts ship with sealant on the PT thread, and only the M5 sizes in this catalogue use a sealing gasket instead. The tube itself is fully re-releasable - press the release ring square to the body to free the Dia 6 tube - but AirTAC publishes no rated number of release cycles.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL601
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.