Airtac PLL L-Type Extended Thread Connector PLL602D
The AirTAC Airtac PLL L-Type Extended Thread Connector PLL602D is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL602D
The PLL602D is an AirTAC PLL extended male elbow: a one-touch elbow whose male thread is lengthened beyond that of the standard PL, so the sealant-coated 1/4 in PT stud stands further clear of the elbow body and leaves room for a nut, wrench flats or a recessed port. It joins Dia 6 mm soft nylon or polyurethane tubing to that thread, and the D suffix makes the body black instead of the standard grey.
Push the tube into the chuck and the stainless spring gasket grips it for a pressure-tight joint; press the POM release ring to free it again. This is the resin and brass profile, not the metal line: 0 to 1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. The threaded stud carries factory-applied sealant, so no extra tape or compound is needed.
Airtac PLL L-Type Extended Thread Connector PLL602D Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL602D |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL602D
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL602D Is Used
Pick-and-place gantry cylinder ports
On Cartesian handling gantries the vertical-actuator port often sits inside a narrow extrusion channel. The extended 1/4 in PT stud reaches past the channel wall, and the black body blends with the anodised frame.
Valve manifold outlets behind dark guards
Where a solenoid manifold is mounted inside a tinted or enclosed guard on packaging equipment, the PLL602D turns the outlet 90 degrees immediately, keeping the Dia 6 drop leg to the actuator short and clean.
Machine control panels with black hardware
OEM panels built to a uniform black hardware scheme use this elbow where tubing exits a bulkhead or fitting plate, so the visible Dia 6 pneumatic drop matches the black pushbuttons and conduit around it.
Is the Airtac PLL L-Type Extended Thread Connector PLL602D the Right Part?
On the 1/4 in PT rung of the PLL ladder this Dia 6 model sits between PLL402 below and PLL802 above. Step down to Dia 4 for small pilot lines and signal circuits, or up to Dia 8 when the same port feeds a hungrier cylinder; the elbow body grows with the bore. If the thread is the fixed point and the port is shallower, the plain PL602 elbow has the shorter stud instead.
Match the black PLL body where a grey fitting would show against dark guarding or machine panels. Whatever the colour, the tube must be Dia 6 exactly: the chuck will not seal on 1/4 in imperial tube, which is a different outside diameter.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL602D FAQ
This SKU is a Dia 6 mm tube one-touch extended male elbow with a 1/4 in PT male thread and a black body. Working pressure is 0 to 1.0 MPa (0 to 10 kgf/cm2), vacuum rating is -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the service temperature range is -20 to +70 C. It suits soft nylon or polyurethane tubing only, and the thread arrives with sealant already applied.
No. On PLL fittings the D suffix changes the body colour to black; the dimensions, the Dia 6 mm chuck, the 1/4 in PT stud, the sealant and every pressure and temperature figure are identical to the grey version. Choose the D code for appearance and machine colour-scheme reasons, not for any performance difference.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL602D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.