Airtac PLL L-Type Extended Thread Connector PLL602D-S
SUS304 stainless variant (-S)The AirTAC Airtac PLL L-Type Extended Thread Connector PLL602D-S is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL602D-S
The PLL602D-S is an AirTAC PLL extended male elbow, the version of the one-touch elbow range whose male thread sits further out from the bend than a standard PL. It joins Dia 6 mm soft nylon or polyurethane tube to a 1/4in PT male port at 90 degrees. To make the joint, push the tube straight in until it bottoms: the stainless spring gasket and chuck grip the OD, and pressing the POM release ring lets the tube out again.
The -S suffix makes the thread stud SUS304 stainless steel while the elbow body stays glass-reinforced PBT, finished black because of the D code in the ordering number. Ratings are identical to the standard PLL line: 0-1.0 MPa working, 1.5 MPa proof, -750 mmHg vacuum, -20 to +70 C. The threaded stud arrives with sealant already applied, so it can be screwed straight into the port.
Airtac PLL L-Type Extended Thread Connector PLL602D-S Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL602D-S |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL602D-S
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL602D-S Is Used
Cylinder ports behind sheet-metal guards
On a packaging machine where the cylinder port sits close to a guard panel, the extended PLL602D-S stud clears the panel so the 6 mm tube can be serviced without dismantling the guard.
Wash-down conveyor take-offs
On food-line conveyor frames cleaned with caustic spray, the SUS304 stud on the 1/4in PT port resists thread corrosion while the black PBT elbow turns the run toward the valve manifold.
Plating and pickling line actuation
Acid fumes attack brass threads on plating-line clamp cylinders; the stainless stud of this Dia 6 elbow survives the atmosphere and the 90-degree turn routes tube along the tank rim.
Is the Airtac PLL L-Type Extended Thread Connector PLL602D-S the Right Part?
On the 1/4in thread rung of the PLL ladder the neighbours are Dia 4 below and Dia 8 above. Stepping to PLL402 drops the bore for short signal lines and small pilot actuators; stepping to PLL802 raises it for cylinders and valves that draw more air. If the port is 1/8in instead, the same 6 mm tube is served by PLL601 - check the drawing before ordering, because thread and tube are ordered independently.
The extension is the reason to pick PLL over PL: it puts the release ring far enough from the wall of a guard or housing that a fingertip can reach it for tube removal. Remember that tube OD must match exactly - a Dia 6 chuck will not seal on 1/4in (6.35 mm) imperial tube, and no adapter exists for that mismatch in this range.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL602D-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg, proof pressure 1.5 MPa, operating temperature -20 to +70 C. The fitting joins Dia 6 mm soft nylon or polyurethane tube to a 1/4in PT male thread, and the thread stud is SUS304 stainless steel on this -S variant.
It changes only the material of the male thread stud, which becomes SUS304. The elbow body remains PBT (black, per the D suffix) and the pressure, vacuum and temperature figures are exactly those of the standard PLL602D. AirTAC does not publish a corrosion class or food certification for the -S line, so the fitting is specified on the material itself, not on a certified rating.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL602D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.