Airtac PLL L-Type Extended Thread Connector PLL6M5
The AirTAC Airtac PLL L-Type Extended Thread Connector PLL6M5 is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL6M5
The AirTAC PLL6M5 is a resin extended male elbow from the PLL series: a one-touch push-in fitting that joins Dia 6 mm soft nylon or polyurethane tube to an M5x0.8 male thread. The extended body puts a longer threaded neck between the swivel face and the elbow, so the tube exits at 90 degrees without fouling adjacent ports. Push the tube home and the stainless spring gasket inside the chuck grips it against the guide; press the POM release ring to free it.
This is the resin and brass spec profile, not the metal line: 0-1.0 MPa working pressure (0-10 kgf/cm2), -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70 C. The threaded body is PBT with a brass stud, and the O-ring is NBR. A detail worth knowing on this SKU: because the thread is M5, it arrives with a sealing gasket rather than the pre-applied thread sealant used on larger tapered threads, so no extra PTFE tape is needed on the male thread.
Airtac PLL L-Type Extended Thread Connector PLL6M5 Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL6M5 |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL6M5
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL6M5 Is Used
Mini cylinder ports inside tight guards
The extended neck of the PLL6M5 lets a Dia 6 mm tube clear a recessed cylinder port on a compact gripper or stopper cylinder, with the 90 degree exit running the line flat along the machine frame instead of into the guard wall.
M5 manifold and valve stations
Compact valve manifolds on packaging and assembly machines use M5x0.8 ports spaced closely together. The gasket-sealed thread and extended elbow keep neighbouring fittings from clashing while feeding 6 mm tube to each actuator branch.
Small-bore lines on analytical equipment
On laboratory and diagnostic instruments with dense pneumatic layouts, the grey PBT PLL6M5 routes 6 mm tubing around tight corners from M5 ports to small pneumatic drives, at the 0-1.0 MPa and -20 to +70 C envelope those devices work in.
Is the Airtac PLL L-Type Extended Thread Connector PLL6M5 the Right Part?
On the M5 ladder for PLL, only Dia 4 and Dia 6 tubes exist, so PLL6M5 is the largest M5 elbow AirTAC makes. Step down to PLL4M5 for 4 mm signal and pilot lines; step up in capacity by moving to the 1/8 inch thread, where PLL601 keeps the same 6 mm tube on a bigger, sealant-coated port. There is no 8 mm tube option on M5.
Match the thread to the port first: M5 is the small metric port found on compact valves, manifolds and mini cylinders, and the gasket-sealed male thread saves assembly time in those crowded locations. Choose the extended PLL shape over a plain PL when the port sits recessed behind a guard, a bracket or a coil housing. Whatever you order, the tube OD must match exactly - this chuck holds 6 mm tube and will not seal on 1/4 inch (6.35 mm) imperial tubing.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL6M5 FAQ
The PLL6M5 is a PLL extended male elbow one-touch fitting for Dia 6 mm tube on an M5x0.8 PT-standard male thread. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. It suits soft nylon or polyurethane tubing, has a POM release button and chuck, an aluminium-alloy guide, a stainless spring gasket, an NBR O-ring, a PBT threaded body and a brass stud, and ships in the standard grey finish.
No to both, in the ways that matter. The chuck is sized for exactly 6 mm metric tube; 1/4 inch (6.35 mm) tube will not seal in it, so match the OD exactly. On the thread side, the M5 size arrives with a sealing gasket rather than pre-applied sealant, which is AirTAC's standard practice on M5 and means no PTFE tape is required on the male thread. If your port is 1/8 inch PT instead, order PLL601, the same 6 mm tube size on that thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL6M5
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.