Airtac PLL L-Type Extended Thread Connector PLL802
The AirTAC Airtac PLL L-Type Extended Thread Connector PLL802 is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL802
The PLL802 is an AirTAC PLL extended male elbow from the resin one-touch range. It joins Dia 8 mm soft nylon or polyurethane tube to a 1/4in PT male thread in a single 90 degree body. The longer male thread compared with the standard PL elbow is the whole point of this prefix: you can screw it further into the port, and the elbow swings to the angle you need before the sealant beds down. To make the joint, push the tube into the chuck until it seats, and the stainless spring gasket and NBR O-ring close around it; press the POM release ring to free the tube again. The 1/4in thread arrives with sealant already applied, so it goes on the port and seals straight away.
This is the resin and brass profile, not the metal BP line: working pressure 0-1.0 MPa, vacuum down to -750 mmHg, proof pressure 1.5 MPa, and a temperature window of -20 to +70 C. The body is PBT over a brass stud, and the grey finish shown here is standard - on the PLL series a D suffix changes the whole body to black, not just the release button as on PC and POC.
Airtac PLL L-Type Extended Thread Connector PLL802 Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL802 |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL802
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL802 Is Used
Robotic gripper cylinder ports
On a pick-and-place head, the angle cylinder port often sits recessed between the gripper body and the harness. The PLL802's extended male thread reaches past the surrounding material and the elbow turns to route 8mm tubing down the arm without kinking.
Packaging machine valve manifolds
PT-threaded solenoid manifold stations on a horizontal flow-wrapper are densely pitched. An extended elbow on a 1/4in port points the 8mm drop toward the bagger actuator instead of across the neighbouring station's fittings.
Conveyor stopper and gate cylinders
Stopper cylinders mounted under a conveyor side rail leave little straight clearance above the port. The PLL802 screws deep into the 1/4in port and angles the Dia 8 airline back along the frame to the junction box.
Is the Airtac PLL L-Type Extended Thread Connector PLL802 the Right Part?
On the PLL 1/4in ladder this Dia 8 sits between PLL602 (Dia 6) and PLL1002 (Dia 10). Stepping to 6 trades capacity for a slimmer elbow in packed guards; stepping to 10 feeds larger-bore actuators that need more volume per stroke. If the shape you want is a straight drop from the port rather than an angled one, that is the PC or POC connector instead of PLL. And remember the one-touch rule: the chuck grips a Dia 8 OD only, so a 5/16in or 1/4in ID hose will not clamp here - tube OD has to be exactly 8 mm.
Match the male thread to the port: 1/4in PT suits the common valve-manifold and cylinder port on machines built to the PT standard. This catalogue documents PT only, so do not order this code against a G or NPT port without an adapter.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL802 FAQ
It is an AirTAC PLL extended male elbow for Dia 8 mm tube with a 1/4in PT male thread. Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C, and soft nylon or polyurethane tubing only. It carries the resin/brass spec profile, so it is rated 0.1 MPa higher and 80 C colder than the metal BPC family.
Both join Dia 8 tube to a 1/4in PT port at 90 degrees, but the PLL is the extended male elbow: its longer male thread lets you engage more of the port and orient the elbow after tightening, which matters where the port is recessed or the sealing face is deep. Use the PL when the thread boss is short and close to obstructions instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL802
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.