Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D
The AirTAC Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D is a genuine bulkhead connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeBulkhead connector
- SeriesPMF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D
The PMF1002D is an AirTAC PMF bulkhead connector, the one-touch fitting made to carry a pneumatic line through a sheet-metal wall. The body mounts in a panel cut-out and is clamped with its M20x1 locknut, the Dia 10 mm soft nylon or polyurethane tube pushes into the outward face, and the 1/4in PT male thread on the inner face screws into the valve, manifold or cylinder port behind the panel. The D suffix specifies the black body version, which many OEMs order so the fitting disappears against painted machine sheet metal.
This is a resin and brass one-touch part, not a metal-line fitting: working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. The body is PBT with a brass stud, the release button and chuck are POM, and the thread arrives with sealant already applied, so it can be screwed straight into a PT port without extra sealing tape. Push the tube fully home and the stainless spring gasket and chuck grip it; press the release ring to free it.
Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D Technical Specifications
| Model | Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D |
|---|---|
| Type | Bulkhead connector |
| Series | PMF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D
| PMF | Bulkhead connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D Is Used
Packaging machine control cabinet
Feed air from the valve manifold inside a form-fill-seal machine's electrical cabinet out to a vacuum ejector on the frame, with the release button left accessible outside the panel for fast tube changes.
Rotary indexing table guard
Pass the supply line through the sheet-metal guard of an indexing dial so the solenoid valve sits protected inside while the Dia 10 hose to the clamp cylinder connects cleanly on the outside.
Workshop air distribution board
Build bulkhead outlets into a maintenance panel or test bench so technicians plug Dia 10 tool lines into the front face while the plumbing behind the board stays on threaded 1/4in PT connections.
Is the Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D the Right Part?
Within the PMF ladder, PMF8-02 steps down to Dia 8 tube on the same 1/4in thread, and PMF12-02 steps up to Dia 12; the locknut thread changes with the tube, M16x1 on Dia 8 and M22x1 on Dia 12, so check the panel hole size before swapping. On the thread side, PMF1001 drops to 1/8in PT and PMF1003 rises to 3/8in PT for larger ports. If you only need a tube connection on both sides of the panel and no male thread, the PM bulkhead union is the simpler part.
Tube OD must match exactly. A Dia 10 fitting will not securely hold 3/8in OD tube, which measures 9.5 mm, and it will not hold 12 mm tube either; order PMF1202D for the Dia 12 line instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D FAQ
It joins a Dia 10 mm tube to a 1/4in PT male thread through a panel wall. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa and temperature range -20 to +70 C. The bulkhead locknut thread for Dia 10 is M20x1. It is a resin-line PBT and brass part with pre-applied thread sealant.
The locknut is M20x1, so cut the panel hole to suit that thread plus clearance for the hex. On tubing: no, only genuine Dia 10 mm soft nylon or polyurethane tube will seal. 3/8in OD tube measures 9.5 mm and will not be gripped by the chuck, so it would leak or blow off under pressure. Use PMF8-02 or PMF12-02 if your line is Dia 8 or Dia 12 instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF1002D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.