Airtac POC Round Thread Straight Connector POC801D
The AirTAC Airtac POC Round Thread Straight Connector POC801D is a genuine male connector (compact) for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale connector (compact)
- SeriesPOC
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac POC Round Thread Straight Connector POC801D
The POC801D is an AirTAC POC male connector in the compact one-touch range - the shorter-bodied alternative to the standard PC when port spacing is tight. It joins Dia 8 mm soft nylon or polyurethane tubing to a 1/8 in PT male thread. Push the tube squarely into the chuck and the stainless spring gasket grips it for a sealed joint; press the POM release ring and the tube slides free for rework.
POC801D runs on the resin/brass spec profile: 0-1.0 MPa (0-10 kgf/cm2) working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70 C. The D suffix is worth noting on this series: on POC it changes only the release button to black, not the whole body, so the fitting still presents grey in the machine and every pressure figure stays identical to the grey version.
Airtac POC Round Thread Straight Connector POC801D Technical Specifications
| Model | Airtac POC Round Thread Straight Connector POC801D |
|---|---|
| Type | Male connector (compact) |
| Series | POC |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac POC Round Thread Straight Connector POC801D
| POC | Male connector (compact). |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac POC Round Thread Straight Connector POC801D Is Used
Solenoid valve outlet on packaging machinery
The short POC body fits the crowded outlet row of a valve manifold on a form-fill-seal machine, where full-length PC connectors would foul adjacent ports on the 1/8 in outlets.
Small pneumatic cylinder port on an assembly fixture
A 1/8 in PT port on a compact bore cylinder or rotary actuator on an electronics assembly fixture takes the POC801D directly, feeding Dia 8 tubing back to the control cabinet.
Manifold branch feed on a printing or converting line
Dia 8 tube steps down from a main air distribution run to individual 1/8 in threaded branches on a printing press vacuum plate circuit, with push-in release making seasonal rework fast.
Is the Airtac POC Round Thread Straight Connector POC801D the Right Part?
On the 1/8 in thread row of the POC ladder, Dia 8 sits between POC601 (Dia 6) and POC1001 (Dia 10). Stepping down to Dia 6 buys a slightly slimmer tube run for light-duty circuits; stepping up to Dia 10 lowers resistance on longer feeds to larger actuators. If the port takes a 1/4 in thread instead, move to POC802 and note that the POC 1/4 in row extends to Dia 12, which 1/8 in does not. Tubing OD must match the fitting exactly - a Dia 8 POC will not seal on 1/4 in (6.35 mm) imperial tube.
Choose the compact POC body over the standard PC when valve stations or manifold blocks leave less than a full-length connector of clearance between ports. For panel or bracket pass-throughs, a PMF bulkhead connector is the right shape instead, since the POC has no mounting feature.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac POC Round Thread Straight Connector POC801D FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Size: Dia 8 mm tubing on a 1/8 in PT male thread, grey body with black release button. Tubing must be soft nylon or polyurethane.
No. On the POC series the D suffix changes only the release button to black; the body and the brass threaded stud stay standard. Pressure, temperature and dimensional data are identical to the grey POC801, so you can interchange the two codes freely in a build. Threaded parts arrive with sealant already applied; only the M5 sizes in the range use a gasket instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac POC Round Thread Straight Connector POC801D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.