The AirTAC Airtac TR Twin-Rod Cylinders TR10X20S is a genuine TR twin-rod (double-rod) double-acting cylinder, 10 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 78.6 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range. As the JIS guide-grade series it adds high non-rotating precision, a lengthening sliding guide (no added lubricant) and two-side ports.
This TR twin-rod cylinder uses two parallel rods on one shared plate, so the plate resists bending and twisting and carries the load without rotating - a built-in guide for transfer and clamp motions. The 10 mm bore with a 20 mm stroke gives a theoretical push thrust of 78.5 N at 0.5 MPa (pull side is lower), while the external bumper both cushions end-of-stroke impact and adjusts the effective stroke over -5 to 0 mm. It runs on air filtered to 40 um at 30-500 mm/s.
It is a genuine AirTAC part to the JIS standard, featuring the TR's precise guide with high non-rotating accuracy, low rod-end deflection, and a lengthening sliding-support guide that needs no added lubricant. Two groups of ports, one on each side of the body, make plumbing flexible, and the magnet is fitted as standard with switch slots around the body. Dimensions for this stroke are confirmed from the datasheet on request.
| Model | Airtac TR Twin-Rod Cylinders TR10X20S |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TR (JIS standard) |
| Bore | 10 mm |
| Push thrust @0.5 MPa | 78.6 N |
| Port size | M5x0.8 (PT, G or NPT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.2 - 1.0 MPa (29 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
This 10 mm bore delivers 78.5 N theoretical push at 0.5 MPa and operates at 0.2-1.0 MPa (29-145 psi); if your load needs more, the same TR series goes up through 16, 20, 25 and 32 mm bores. The 20 mm stroke is a listed length for this bore - choose from the bore's stroke table and keep strokes within the short-cover range rather than stretching them. The thread on this code is PT; TR also comes in G and NPT. If you can accept the enterprise-standard TN (10-32 mm bores, PT only) instead, it omits the TR's precise guide, no-lube sliding support and two-side ports. Allowable side load is given only as datasheet curves - send us your load case and we will confirm it.
Pushes small bins into position on a palletizing cell; the anti-rotation twin-rod plate keeps the push face square across the full 20 mm stroke.
Advances sample trays on a benchtop indexing station, where the TR's precise guide and low rod-end deflection hold repeatable tray positions.
Swing-gate or escapement stop on a parts feed line; the bumper cushions each part arrival and trims the stop setting by up to 5 mm.
Both are double-acting twin-rod cylinders with a standard magnet. The TN is the enterprise standard, covers 10-32 mm bores and is PT-thread only. The TR is the JIS-standard guide-grade version with higher non-rotating accuracy, low rod-end deflection, a lengthening sliding-support guide that needs no added lubricant, two groups of ports (one each side), and a choice of PT, G or NPT threads. This TR10X20S code is PT; order a G or NPT variant if your fittings require it.
The twin-rod construction resists rotation, bending and twisting, and the TR guide keeps rod-end deflection low, so modest off-center loads are its strength. However, allowable side load is published only as curves, not as a single number, so check your load against the datasheet or ask us to confirm it before mounting. The same applies to overall dimensions, which vary with the 20 mm stroke.