Airtac BSE Clamp Standard Cylinder BSE32X350
The AirTAC Airtac BSE Clamp Standard Cylinder BSE32X350 is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø12mm rod and holds up to 600 N in either direction — no drift. Ø32mm bore, 350mm stroke, PT1/8 cylinder ports, G1/8 lock-release port.
- BoreØ32 mm
- Stroke350 mm
- Static holding force600 N
- Lock typeSpring-lock / air-release
- Cylinder portPT1/8
- Lock-release portG1/8
About the Airtac BSE Clamp Standard Cylinder BSE32X350
The AirTAC BSE32X200 is a double-acting ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. It delivers a 600 N bidirectional static holding force with no live air, ensuring suspended loads stay fixed if air pressure drops. Operating pressure is capped at 0.7 MPa, and the separate G1/8 release port governs the collet mechanism.
This 32 mm bore, 350 mm stroke unit uses a PT1/8 cylinder port and a 27 mm adjustable air cushion at both ends. Because this SKU lacks the -S magnet option, it does not support position sensing. The lock engages only after the piston stops, requiring at least 0.5 s for full release before motion resumes.
Rod Lock — 600 N Static Holding (Ø32mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE32X350 holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE32X350 Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE32X350 |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø32 mm |
| Stroke | 350 mm |
| Static holding force | 600 N |
| Cylinder port | PT1/8 |
| Lock-release port | G1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 700 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa (max) | 563 N | — |
| Max drive (@0.7 MPa) | 57 kgf | |
Drive force is separate from the 600 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE32X350
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 32 | Bore size in mm. |
| ×350 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE32X350 Is Used
Small Vertical Lift
Holds a 600 N vertical pick-and-place head in place during an E-stop, preventing drift when main air is exhausted.
Tool Clamp Hold
Secures a light machining fixture with 563 N push force, locking the 12 mm rod instantly if supply pressure drops below 0.15 MPa.
Pneumatic Stop Gate
Maintains a conveyor stop gate position securely at 350 mm extension using the spring-applied collet, even during full air loss.
Is the Airtac BSE Clamp Standard Cylinder BSE32X350 the Right Cylinder?
Verify your load requires 600 N or less of holding force, and check that the 563 N push force at 0.7 MPa is sufficient. If you need less drive, the adjacent bore down is unavailable, so this is the smallest fail-safe option. If you need more hold, step up to the 40 mm bore, which provides 900 N holding force and 628 N push at 0.5 MPa. At 350 mm stroke, use a guide to prevent side-load wear on the seals.
Always engage the lock only after the rod stops, and release it only when piston pressures are balanced. This cylinder uses a PT1/8 port, basic mounting, and no magnet. SE mounting accessories fit this body, except FTC.
Quick checklist
- ✓ Load to hold ≤ 600 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE32X350 FAQ
The lock is spring-applied and fails safe, delivering 600 N of static holding force in both directions if air is lost. The drive forces are 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and max drive is 57 kgf.
You must supply 0.15-0.7 MPa to the separate G1/8 release port, but only after balancing pressures on both sides of the piston. Allow at least 0.5 s for the collet to fully release before commanding cylinder motion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE32X350
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.