Airtac BSE Clamp Standard Cylinder BSE80X600
The AirTAC Airtac BSE Clamp Standard Cylinder BSE80X600 is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø25mm rod and holds up to 3600 N in either direction — no drift. Ø80mm bore, 600mm stroke, PT3/8 cylinder ports, G1/8 lock-release port.
- BoreØ80 mm
- Stroke600 mm
- Static holding force3600 N
- Lock typeSpring-lock / air-release
- Cylinder portPT3/8
- Lock-release portG1/8
About the Airtac BSE Clamp Standard Cylinder BSE80X600
The AirTAC BSE80X600 is a double-acting ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. It delivers a 3600 N bidirectional static holding force with no live air, preventing drift on suspended loads. Operating pressure is capped at 0.7 MPa.
This 80 mm bore, 600 mm stroke unit uses a Ø25 mm rod and PT3/8 cylinder ports, while a separate G1/8 port unlocks the collet. This SKU has no magnet, meaning position sensing is not supported. The lock is a holding device, not a dynamic brake.
Rod Lock — 3600 N Static Holding (Ø80mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE80X600 holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE80X600 Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE80X600 |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø80 mm |
| Stroke | 600 mm |
| Static holding force | 3600 N |
| Cylinder port | PT3/8 |
| Lock-release port | G1/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa (max) | 3519 N | — |
| Max drive (@0.7 MPa) | 359 kgf | |
Drive force is separate from the 3600 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE80X600
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 80 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE80X600 Is Used
Vertical Pallet Lift
Holds a raised pallet station securely with 3600 N of fail-safe force, preventing a crash if compressed air is lost mid-cycle.
Heavy Tooling Clamp
Keeps a machining fixture clamped during an E-stop, using the spring-applied collet to resist vibration while the 3518 N drive positions the part.
Pallet Stop Gate
Acts as a rigid stop gate on a 600 mm stroke that stays firmly extended during air exhaustion, halting heavy conveyor flow without drifting.
Is the Airtac BSE Clamp Standard Cylinder BSE80X600 the Right Cylinder?
Verify your load needs 3600 N or less of static holding force. If you need less, the 63 mm bore offers 1402 N push at 0.5 MPa and 2200 N holding force. If you need more, the 100 mm bore provides 3927 N push at 0.5 MPa and 5500 N holding force.
At 600 mm of stroke, use a guide to prevent side-load damage to the seal. Engage the lock only after the rod stops, and release it only when piston pressures are balanced, allowing at least 0.5 s before moving. Match the bore, stroke, PT thread, and mounting when replacing.
Quick checklist
- ✓ Load to hold ≤ 3600 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE80X600 FAQ
On air loss, the spring-applied collet clamps the rod for a 3600 N static hold. The drive forces are 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, with a max drive of 359 kgf.
Balance the air pressure on both sides of the piston first. Then supply air to the G1/8 release port at 0.15-0.7 MPa, and wait at least 0.5 seconds before commanding cylinder movement to ensure full release.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE80X600
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.