Airtac BSED Clamping Double Acting Cylinder BSED32X100
The AirTAC Airtac BSED Clamping Double Acting Cylinder BSED32X100 combines a double-rod ISO 15552 cylinder — a Ø12mm rod out BOTH ends for equal force both directions — with an integrated spring-applied, air-released ROD LOCK that holds up to 600 N in either direction if air is lost. Ø32mm bore, 100mm stroke, PT1/8 ports, G1/8 lock-release.
- BoreØ32 mm
- Stroke100 mm
- Static holding force600 N
- ConfigurationDouble rod + lock
- Cylinder portPT1/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSED Clamping Double Acting Cylinder BSED32X100
The AirTAC BSED32X100 is a double-acting, double-rod ISO 15552 profile cylinder featuring an integrated spring-applied, air-released rod lock. A rod exits both ends, delivering equal drive force of 345 N each way at 0.5 MPa. The internal collet mechanism provides a bidirectional fail-safe holding force of 600 N with zero live air required.
This 32 mm bore unit features a PT1/8 cylinder port and a separate G1/8 lock-release port. The extruded aluminum barrel omits external tie rods for a clean ISO 15552 mounting interface. This specific SKU lacks a magnet, so it does not support CMSE or DMSE position sensors.
Double Rod + 600 N Rod Lock (Ø32mm)
A rod exits both ends for symmetric force and back-rod tooling, and a spring clamps the collet so the Airtac BSED Clamping Double Acting Cylinder BSED32X100 holds its position in both directions on air loss or E-stop. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage only after the rod has stopped (not a dynamic brake), and release only when both piston sides are pressure-balanced; allow ≥0.5 s for full release.
Airtac BSED Clamping Double Acting Cylinder BSED32X100 Technical Specifications
| Model | Airtac BSED Clamping Double Acting Cylinder BSED32X100 |
|---|---|
| Series | BSED ISO 15552 double-rod rod-lock cylinder |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Static holding force | 600 N |
| Cylinder port | PT1/8 |
| Lock-release port | G1/8 |
| Configuration | Double rod, double acting |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Max stroke | Up to 700 mm |
Specifications follow the official AirTAC BSED datasheet. Rod thread M10×1.25 both ends. Mounting (BSED): Basic, LB, FA, TC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa (max) | 484 N |
| Max drive (@0.7 MPa) | 49 kgf |
A rod exits both ends, so force is equal on extend and retract. Drive force is separate from the 600 N static lock holding force. Size with a safety margin.
Model Code: Airtac BSED Clamping Double Acting Cylinder BSED32X100
| B | Rod-lock cylinder prefix. |
|---|---|
| SED | ISO 15552 double-rod double-acting body. |
| 32 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSED): Basic, LB, FA, TC. Related: SED (double rod, no lock), BSE (single-rod rod lock). Sensors CMSE/DMSE fit magnetic BSED.
Where the Airtac BSED Clamping Double Acting Cylinder BSED32X100 Is Used
Vertical Lift Stops
Secure vertical pick-and-place loads with 600 N of static holding force, preventing drops if air pressure drops suddenly during operation.
Symmetric Tooling Mount
Utilize the equal 345 N both-way drive force to mount identical tooling on both rods, ensuring balanced actuation for precision clamping.
Anti-Rotation Indexing
Leverage the double-rod design to resist mechanical rotation, using the rear rod for a flag cam while the lock holds position mid-stroke.
Is the Airtac BSED Clamping Double Acting Cylinder BSED32X100 the Right Cylinder?
Select this 32 mm bore model when your application requires symmetric both-way force and a fail-safe hold up to 600 N. If your load demands less hold, no smaller BSED bore exists. If you need more force, stepping up to the 40 mm bore yields 528 N drive force at 0.5 MPa and a 900 N holding force. Always engage the lock only after the rod stops moving, and release it only when both piston sides are pressure-balanced, allowing at least 0.5 seconds.
When replacing a unit, verify the 100 mm stroke, PT1/8 port, M10x1.25 rod thread, and your mounting style (Basic, LB, FA, or TC). Operating pressure is capped at 0.7 MPa, and the lock requires a separate G1/8 supply. Because the stroke is under 300 mm, standard side-load risks are minimized, but always verify guide alignment.
Quick checklist
- ✓ Need both symmetric force AND fail-safe hold?
- ✓ Load to hold ≤ 600 N?
- ✓ Back-rod space for tooling/flag
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Support both rod ends; avoid side load.
- check Use BSED mounting (Basic/LB/FA/TC).
Airtac BSED Clamping Double Acting Cylinder BSED32X100 FAQ
The integrated rod lock is spring-applied, meaning it automatically clamps the rod if air is lost or an E-stop trips, providing a 600 N bidirectional static hold. It is not a dynamic brake, so you must engage it only after the rod stops moving.
The BSED32X100 delivers equal both-way drive force of 345 N at 0.5 MPa and 483 N at 0.7 MPa (max 49 kgf). The static fail-safe holding force of the lock is 600 N. Release the lock only when both piston sides are pressure-balanced.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSED Cylinders
Request a Quote for Airtac BSED Clamping Double Acting Cylinder BSED32X100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.