Airtac BSED Clamping Double Acting Cylinder BSED63X25S
The AirTAC Airtac BSED Clamping Double Acting Cylinder BSED63X25S combines a double-rod ISO 15552 cylinder — a Ø20mm rod out BOTH ends for equal force both directions — with an integrated spring-applied, air-released ROD LOCK that holds up to 2200 N in either direction if air is lost. Ø63mm bore, 25mm stroke, PT3/8 ports, G1/8 lock-release.
- BoreØ63 mm
- Stroke25 mm
- Static holding force2200 N
- ConfigurationDouble rod + lock
- Cylinder portPT3/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSED Clamping Double Acting Cylinder BSED63X25S
The AirTAC BSED63X25S is a double-acting, double-rod ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. A rod exits both ends, providing equal drive force of 1402 N each way at 0.5 MPa and a maximum of 1962 N at 0.7 MPa. The extruded aluminum barrel has no external tie rods, ensuring a clean ISO 15552 mounting interface.
The fail-safe collet delivers a 2200 N static holding force with no live air, clamping the Ø20 mm rod bidirectionally if pressure drops. A separate G1/8 release port controls the lock, and the -S magnet supports CMSE reed and DMSE electronic sensors for position tracking.
Double Rod + 2200 N Rod Lock (Ø63mm)
A rod exits both ends for symmetric force and back-rod tooling, and a spring clamps the collet so the Airtac BSED Clamping Double Acting Cylinder BSED63X25S holds its position in both directions on air loss or E-stop. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage only after the rod has stopped (not a dynamic brake), and release only when both piston sides are pressure-balanced; allow ≥0.5 s for full release.
Airtac BSED Clamping Double Acting Cylinder BSED63X25S Technical Specifications
| Model | Airtac BSED Clamping Double Acting Cylinder BSED63X25S |
|---|---|
| Series | BSED ISO 15552 double-rod rod-lock cylinder |
| Bore size | Ø63 mm |
| Stroke | 25 mm |
| Static holding force | 2200 N |
| Cylinder port | PT3/8 |
| Lock-release port | G1/8 |
| Configuration | Double rod, double acting |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSED datasheet. Rod thread M16×1.5 both ends. Mounting (BSED): Basic, LB, FA, TC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa (max) | 1962 N |
| Max drive (@0.7 MPa) | 200 kgf |
A rod exits both ends, so force is equal on extend and retract. Drive force is separate from the 2200 N static lock holding force. Size with a safety margin.
Model Code: Airtac BSED Clamping Double Acting Cylinder BSED63X25S
| B | Rod-lock cylinder prefix. |
|---|---|
| SED | ISO 15552 double-rod double-acting body. |
| 63 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSED): Basic, LB, FA, TC. Related: SED (double rod, no lock), BSE (single-rod rod lock). Sensors CMSE/DMSE fit magnetic BSED.
Where the Airtac BSED Clamping Double Acting Cylinder BSED63X25S Is Used
Vertical Lift Stations
Holds a 2200 N vertical load securely during an E-stop or air loss, while the 1962 N equal both-way force drives the lift up and down reliably.
Symmetric Transfer Units
Uses the rear rod for cam tracking while the front rod pushes and pulls an 1402 N load at 0.5 MPa with identical speed in both directions.
Mid-Stroke Machining
Clamps the Ø20 mm rod at a precise 25 mm interval for machining, preventing drift without relying on the air cushion for static hold.
Is the Airtac BSED Clamping Double Acting Cylinder BSED63X25S the Right Cylinder?
Select this 63 mm bore when an application needs symmetric thrust and fail-safe holding up to 2200 N. If your load requires less force, the 50 mm bore offers 825 N at 0.5 MPa and 1400 N holding. If you need more, the 80 mm bore provides 2268 N at 0.5 MPa and 3600 N holding. Always verify the load is below 2200 N and engage the lock only after the rod stops, allowing at least 0.5 s for the pressure-balanced release. For replacement, match the 25 mm stroke, PT3/8 port, and mounting option.
Quick checklist
- ✓ Need both symmetric force AND fail-safe hold?
- ✓ Load to hold ≤ 2200 N?
- ✓ Back-rod space for tooling/flag
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Support both rod ends; avoid side load.
- check Use BSED mounting (Basic/LB/FA/TC).
Airtac BSED Clamping Double Acting Cylinder BSED63X25S FAQ
The drive force is equal both ways at 1402 N @0.5 MPa and 1962 N @0.7 MPa, with a max drive of 200 kgf. The static holding force of the spring-applied rod lock is 2200 N.
If air is lost, the spring-applied collet clamps the rod instantly, providing a 2200 N static hold. To release, both piston sides must be pressure-balanced and the separate G1/8 port must be pressurized, allowing at least 0.5 s for unlock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSED Cylinders
Request a Quote for Airtac BSED Clamping Double Acting Cylinder BSED63X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.