Airtac BSE Clamp Standard Cylinder BSE32X175S
The AirTAC Airtac BSE Clamp Standard Cylinder BSE32X175S is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø12mm rod and holds up to 600 N in either direction — no drift. Ø32mm bore, 175mm stroke, PT1/8 cylinder ports, G1/8 lock-release port.
- BoreØ32 mm
- Stroke175 mm
- Static holding force600 N
- Lock typeSpring-lock / air-release
- Cylinder portPT1/8
- Lock-release portG1/8
About the Airtac BSE Clamp Standard Cylinder BSE32X175S
The AirTAC BSE32X175S is a double-acting ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. A collet clamps the 12mm rod instantly upon air loss, providing a bidirectional fail-safe holding force of 600N. Operating pressure is capped at 0.15-0.7 MPa.
This 32mm bore, 175mm stroke model features a -S magnet for CMSE (reed) and DMSE (electronic) position sensing. The lock uses a separate G1/8 release port; the cylinder itself uses a PT1/8 port. SE-compatible mounting accessories fit this body, except for FTC.
Rod Lock — 600 N Static Holding (Ø32mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE32X175S holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE32X175S Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE32X175S |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Static holding force | 600 N |
| Cylinder port | PT1/8 |
| Lock-release port | G1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 700 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa (max) | 563 N | — |
| Max drive (@0.7 MPa) | 57 kgf | |
Drive force is separate from the 600 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE32X175S
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE32X175S Is Used
Small Vertical Lifts
Holds 600N against gravity on small pneumatic vertical lifts if air drops, preventing payload drift.
Tooling Clamp Hold
Maintains 600N clamping force on light machining tooling during E-stop without needing live air.
Small Gate Stop
Locks a 175mm stroke stop gate firmly in place using the collet lock during conveyor line air loss.
Is the Airtac BSE Clamp Standard Cylinder BSE32X175S the Right Cylinder?
Verify your load does not exceed the 600N static holding force. If you need less drive, the next bore down is unavailable. If you need more, step up to bore 40, which provides 628N push at 0.5 MPa and 900N holding force. Always engage the lock only after the rod fully stops, and allow at least 0.5s for release after balancing piston pressures. For this 175mm stroke, ensure external guides support side loads to prevent binding. Replacement requires matching the 32mm bore, 175mm stroke, PT thread, basic mounting, and -S magnet.
Quick checklist
- ✓ Load to hold ≤ 600 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE32X175S FAQ
It is spring-applied and air-released. If air is lost or exhausted, a collet clamps the rod, providing a 600N bidirectional static hold. It is not a dynamic brake; engage it only after the rod stops.
At 0.5 MPa, push is 402N and pull is 345N. At the 0.7 MPa ceiling, push is 563N with a max drive of 57 kgf. This drive force is separate from the 600N static holding force.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE32X175S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.