Airtac BSE Clamp Standard Cylinder BSE32X600
The AirTAC Airtac BSE Clamp Standard Cylinder BSE32X600 is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø12mm rod and holds up to 600 N in either direction — no drift. Ø32mm bore, 600mm stroke, PT1/8 cylinder ports, G1/8 lock-release port.
- BoreØ32 mm
- Stroke600 mm
- Static holding force600 N
- Lock typeSpring-lock / air-release
- Cylinder portPT1/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSE Clamp Standard Cylinder BSE32X600
The AirTAC BSE32X600 is a double-acting ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. A collet clamps the Ø12 mm rod to provide a 600 N bidirectional static holding force with no live air required. This fail-safe mechanism prevents drifting when air is lost or an E-stop is engaged.
Operating pressure is capped at 0.7 MPa, and the lock uses a separate G1/8 release port. Because this 600 mm stroke lacks the -S magnet option, it cannot mount CMSE or DMSE position sensors. The standard ISO 15552 interface means SE mounting accessories fit perfectly, except FTC.
Rod Lock — 600 N Static Holding (Ø32mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE32X600 holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE32X600 Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE32X600 |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø32 mm |
| Stroke | 600 mm |
| Static holding force | 600 N |
| Cylinder port | PT1/8 |
| Lock-release port | G1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 700 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa (max) | 563 N | — |
| Max drive (@0.7 MPa) | 57 kgf | |
Drive force is separate from the 600 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE32X600
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 32 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE32X600 Is Used
Vertical Pneumatic Lifts
Holds a 600 N vertical load in place on a 32 mm bore lift station if air pressure drops, preventing sudden drops.
Package Stopper Arms
Locks a conveyor diverter arm rigidly mid-cycle during an E-stop, withstanding 600 N of impact without drifting.
Lightweight Tool Clamping
Secures a small machining fixture in position during an air loss event, ensuring 600 N of fail-safe holding.
Is the Airtac BSE Clamp Standard Cylinder BSE32X600 the Right Cylinder?
Verify your suspended load is below the 600 N holding force. If you need less holding capacity, the next bore down is unavailable, but stepping up to a 40 mm bore raises the holding force to 900 N and the 0.5 MPa push to 628 N. If you need more drive force, stepping up to a 40 mm bore increases the 0.5 MPa push to 628 N and the holding force to 900 N.
At 600 mm stroke, prevent side-load damage by guiding the load externally. Engage the lock only after the rod stops, and release it only when piston pressures are balanced, allowing at least 0.5 s before moving. Replacement requires matching the 32 mm bore, 600 mm stroke, PT1/8 port, and basic mounting.
Quick checklist
- ✓ Load to hold ≤ 600 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE32X600 FAQ
The 32 mm bore provides a push force of 402 N and a pull force of 345 N at 0.5 MPa. At the 0.7 MPa ceiling, push is 563 N (max drive 57 kgf). The integrated rod lock provides a separate 600 N bidirectional static holding force with no live air.
The lock is spring-applied and air-released via a separate G1/8 port. You must engage it only after the rod stops, and release it only when pressures on both sides of the piston are balanced, allowing at least 0.5 s for full release before moving.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE32X600
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.