Airtac SE32 Standard Cylinder SE32X600
The AirTAC Airtac SE32 Standard Cylinder SE32X600 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 600mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke600 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X600
The AirTAC SE32X600 is a double-acting single-rod ISO 15552 profile cylinder engineered for compact, space-constrained pneumatics. It generates 402 N of push force at 0.5 MPa and utilizes a PT1/8 port paired with a 12 mm hard-chrome rod. Because the stroke extends to 600 mm, this unit is produced as a non-standard made-to-order configuration to support extended travel requirements.
Unlike traditional round-body cylinders, this model features an extruded aluminum barrel without external tie rods, yielding a smooth, corrosion-resistant exterior that mounts flush against machine frames. The barrel integrates sensor grooves on three sides, although this specific SKU lacks the built-in magnet and cannot host CMSE or DMSE position switches. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration, softening impacts during high-velocity 30-800 mm/s cycling.
Airtac SE32 Standard Cylinder SE32X600 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X600 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X600
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X600 Is Used
PCB Edge Belt Sanding
Drives a 600 mm linear stage for sanding conveyor belts, using the 402 N push force to maintain consistent tensioning on an automated PCB deburring line.
Lab Sample Dispenser
Actuates a 600 mm travel arm to shuttle fluidic test vials between analysis stations, relying on the smooth extruded profile barrel for clean, flush mounting in lab enclosures.
Small Parts Ejection
Pushes lightweight plastic injection-molded components out of a mold cavity over a 600 mm span, utilizing the 30-800 mm/s speed range for rapid cycle times.
Is the Airtac SE32 Standard Cylinder SE32X600 the Right Cylinder?
Stepping down to a smaller bore is not an option since 32 mm is the smallest available SE diameter. If your application requires greater thrust, moving up to the 40 mm bore yields 628 N of push at 0.5 MPa. Because this 600 mm stroke exceeds the 1000 mm standard limit for this bore, it is a non-standard made-to-order item.
At 600 mm of unsupported travel, the 12 mm rod is highly susceptible to bending under side loads; incorporating an external linear guide is strongly recommended to prevent premature seal wear and rod-bearing failure. Note that the adjustable air cushion only decelerates the piston near the stroke ends and will not hold a load if air pressure is lost—use a BSE rod lock for static holding. As a true ISO 15552 cylinder, it is dimensionally interchangeable with other ISO 15552 profile cylinders, sharing identical mounting footprints for straightforward retrofits.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X600 FAQ
The SE32X600 delivers 402 N of push force and 345 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. It features a PT1/8 port and a 12 mm rod with an M10x1.25 thread.
Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing you to reuse existing mounting brackets. However, this specific SKU does not include a built-in magnet, so it cannot support AirTAC CMSE or DMSE position sensors without modifying the piston.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X600
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.